October 20, 2017, 10:04:19 PM

Author Topic: Configurations  (Read 3701 times)

Offline Alan

  • Full Member
  • ***
  • Posts: 110
  • The artist formerly known as Flyalan :-)
    • flyalan
Re: Configurations
« Reply #30 on: June 08, 2017, 11:04:14 AM »
Yes. It will require some trimming. And cutting a new flat spot on the motor side. I have two shafts and a second XNova arriving next week. I will post those results.  It should not be an issue. I have frequently altered motor shafts as needed.

Cheers
Alan


Sent from my iPhone using Tapatalk

Offline Codepox (Guillaume)

  • Field Representative
  • Member
  • ****
  • Posts: 58
Re: Configurations
« Reply #31 on: June 08, 2017, 11:23:47 AM »
OK, I see.
Are you going to cut the bottom and create new flat spots for 2 set screws?
That should work.

Here is a photo of an XNova 4020 shaft:


« Last Edit: June 08, 2017, 01:06:06 PM by codepox (Guillaume) »

Offline Codepox (Guillaume)

  • Field Representative
  • Member
  • ****
  • Posts: 58
Re: Configurations
« Reply #32 on: June 08, 2017, 01:04:00 PM »
Double post

Offline Alan

  • Full Member
  • ***
  • Posts: 110
  • The artist formerly known as Flyalan :-)
    • flyalan
Re: Configurations
« Reply #33 on: June 08, 2017, 01:40:38 PM »
Yes that was the plan in addition to a little shortening.

Cheers

Alan


OK, I see.
Are you going to cut the bottom and create new flat spots for 2 set screws?
That should work.

Here is a photo of an XNova 4020 shaft:

Offline Rob Cherry

  • Factory Pilot
  • Sr. Member
  • *****
  • Posts: 323
Re: Configurations
« Reply #34 on: June 08, 2017, 01:47:11 PM »
Easy enough with a dremel until Xnova comes out with an actual part. :)
Synergy Factory Pilot

Offline TheBum

  • Newbie
  • *
  • Posts: 15
Re: Configurations
« Reply #35 on: June 09, 2017, 12:02:45 PM »
Any chance that the motor pinion options will expand? I have an Xnova 4025-1120 I'd love to use, but in order to get the head speeds I want, I'd need a 20T pinion. Thus far, only 16T-19T pinions have been announced.

Offline Rob Cherry

  • Factory Pilot
  • Sr. Member
  • *****
  • Posts: 323
Re: Configurations
« Reply #36 on: June 09, 2017, 01:16:23 PM »
16-21 have been confirmed. I mentioned it above, but maybe the specs on Matt's site need to be updated.

Sent from my XT1254 using Tapatalk

Synergy Factory Pilot

Offline TheBum

  • Newbie
  • *
  • Posts: 15
Re: Configurations
« Reply #37 on: June 09, 2017, 01:58:25 PM »
16-21 have been confirmed. I mentioned it above, but maybe the specs on Matt's site need to be updated.
Even better! That brings it within the realm of several ~1100Kv motors.

Offline Ross Lawton

  • Factory Specialist
  • Synergy Veteran
  • *****
  • Posts: 788
Re: Configurations
« Reply #38 on: June 10, 2017, 04:09:01 PM »
Itching to get my hands on the 516, my planned config is the following:

Scorpion 4020-1350kv
Castle Creations Talon 90
Futaba BLS173SV Cyclic's
Futaba BLS276SV Tail
Futaba CGY750
Rail 516 and 80.6
Headspeed 2700
Optipower 4300 50c 6s
Team Synergy - UK

Offline Rob Cherry

  • Factory Pilot
  • Sr. Member
  • *****
  • Posts: 323
Re: Configurations
« Reply #39 on: June 10, 2017, 06:13:18 PM »
Itching to get my hands on the 516, my planned config is the following:

Scorpion 4020-1350kv
Castle Creations Talon 90
Futaba BLS173SV Cyclic's
Futaba BLS276SV Tail
Futaba CGY750
Rail 516 and 80.6
Headspeed 2700
Optipower 4300 50c 6s
The futaba minis don't exactly fit. Maybe we should make an announcement so people (and futaba) know. They are 2mm short on each side. They can be made to fit with adapters or large washers, but it's not simply plug an play. :(

Sent from my XT1254 using Tapatalk
Synergy Factory Pilot

Offline Ross Lawton

  • Factory Specialist
  • Synergy Veteran
  • *****
  • Posts: 788
Re: Configurations
« Reply #40 on: June 11, 2017, 12:03:06 PM »
Itching to get my hands on the 516, my planned config is the following:

Scorpion 4020-1350kv
Castle Creations Talon 90
Futaba BLS173SV Cyclic's
Futaba BLS276SV Tail
Futaba CGY750
Rail 516 and 80.6
Headspeed 2700
Optipower 4300 50c 6s
The futaba minis don't exactly fit. Maybe we should make an announcement so people (and futaba) know. They are 2mm short on each side. They can be made to fit with adapters or large washers, but it's not simply plug an play. :(

Sent from my XT1254 using Tapatalk


Gutted, i was looking forward to giving the a try too!  :(
Team Synergy - UK

Offline Josh Easter

  • Field Representative
  • Member
  • ****
  • Posts: 78
  • 812-278-1997
Re: Configurations
« Reply #41 on: June 12, 2017, 02:10:43 PM »
ahhh i can't wait!!

I will run

Scorpion HKlll 4020-1350kv
Scorpion tribunus 06-120 SBEC
MKS HV9767 cyclics
MKS HBL980 tail Maybe I really like the futaba also ;)
Vbar neo with vcontrol

Bring it on Matt!!!
Team Synergy

Offline TheBum

  • Newbie
  • *
  • Posts: 15
Re: Configurations
« Reply #42 on: June 12, 2017, 02:23:03 PM »
Is there a list of cyclics that are known to fit? What dimensions do they need?

Offline Chris Sexton

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2669
  • Admiral, There be whales here!
Configurations
« Reply #43 on: June 12, 2017, 03:26:32 PM »
Is there a list of cyclics that are known to fit? What dimensions do they need?


See Rob's post down 2 posts.


Sent from my iPhone using Tapatalk
« Last Edit: June 12, 2017, 05:34:02 PM by Chris Sexton »
Chris Sexton
Synergy Factory Specialist / Rail Blades / Team Scorpion

Offline Roger

  • Full Member
  • ***
  • Posts: 200
Re: Configurations
« Reply #44 on: June 12, 2017, 04:11:31 PM »
I hope something from the Xpert line fits.
ROG
Retired Old Guy