May 02, 2024, 04:13:15 AM
« previous next »
Pages: [1]

Author Topic: 12-13 pinions availabilty  (Read 3127 times)

Offline lolo

  • Newbie
  • *
  • Posts: 12
12-13 pinions availabilty
« on: October 19, 2011, 05:53:24 AM »
Do you know when these pinions are going to be available?
I think my steup is "a little bit" overkill -> Scorpion 4035-500, Hyperion 12S 4500.
If I use the headspeed calculator from RH, it says:
(calculated for 100% throttle curve)
Hover RPM at beginning of flight: 3047
Hover RPM at middle of flight: 2807
Hover RPM at end of flight: 2709
Thanks
Logged

Offline HelliYea

  • Newbie
  • *
  • Posts: 45
12-13 pinions availabilty
« Reply #1 on: October 19, 2011, 03:36:36 PM »
They are available here in Aus now.  Shouldnt be too far away elsewhere..
Logged

Offline Jean-Luc Bolduc

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 614
Re: 12-13 pinions availabilty
« Reply #2 on: October 19, 2011, 07:57:11 PM »
Just got a 12t and 13t pinion.

You'll most likely need a 12t.

I'm running a 12t on a Xera 4035-500kv motor, 2150 hs on 70% Jive 120 hv  on E7.

Logged
Team Synergy

Offline steffgiguere

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1373
Re: 12-13 pinions availabilty
« Reply #3 on: October 19, 2011, 08:16:07 PM »
Maybe with CC ICE you will, since it's rated lower than Kontronik, that a 13 tooth will suite your needs, need to check in ESC programming.
Logged
Team Synergy, Canada

Offline BennyTRD

  • Newbie
  • *
  • Posts: 20
Re: 12-13 pinions availabilty
« Reply #4 on: October 20, 2011, 07:26:18 AM »
Picked up a Hacker 470 in the meantime while the pinions are still en-route. Performs good but I'm still wanting to try the 4530-500 out. Those who have the 12-13T, where have you guys found the pinions?
Logged

Offline Jean-Luc Bolduc

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 614
Re: 12-13 pinions availabilty
« Reply #5 on: October 20, 2011, 07:36:51 PM »
Sorry , I'm running a Xera  4530 not a 4035 . Love that motor !

I had put an early order for them pinions.

My lhs also ordered some and is receiving them tomorrow.
Logged
Team Synergy

Offline BennyTRD

  • Newbie
  • *
  • Posts: 20
Re: 12-13 pinions availabilty
« Reply #6 on: October 24, 2011, 11:38:28 AM »
Quote from: 4cyclic on October 20, 2011, 07:36:51 PM
Sorry , I'm running a Xera  4530 not a 4035 . Love that motor !

I had put an early order for them pinions.

My lhs also ordered some and is receiving them tomorrow.

Who's your LHS? Im desperate!!
Logged

Offline DAldridge

  • Newbie
  • *
  • Posts: 18
Re: 12-13 pinions availabilty
« Reply #7 on: October 24, 2011, 12:32:09 PM »
I just ordered by E7 and 13T pinion from www.ronlund.com.  I believe ExperienceRC also has them in stock.
Logged

Offline QuantumPSI

  • Newbie
  • *
  • Posts: 10
Re: 12-13 pinions availabilty
« Reply #8 on: November 03, 2011, 07:20:08 PM »
4cyclic, how is the fit with that motor?  Planning on picking up one myself.

Oh and what kind of flight times are you getting?  What batteries?
« Last Edit: November 03, 2011, 07:27:15 PM by QuantumPSI »
Logged

Offline steffgiguere

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1373
Re: 12-13 pinions availabilty
« Reply #9 on: November 03, 2011, 08:00:24 PM »
4 cyclic's LHS is NDHeli. at www.ndheli.com
Logged
Team Synergy, Canada

Offline Jean-Luc Bolduc

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 614
Re: 12-13 pinions availabilty
« Reply #10 on: November 08, 2011, 07:57:47 AM »
Xera motor fits perfect in E7, so is 12t pinion. It meshes without any mods. I did not even cut the shaft, as it is a longer than needed for the support bearing.
Logged
Team Synergy
Pages: [1]
« previous next »