May 08, 2024, 02:52:33 PM
« previous next »
Pages: [1]

Author Topic: Scorpion motor connectors  (Read 3526 times)

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Scorpion motor connectors
« on: January 02, 2013, 05:35:30 PM »
The male end is on the scorpion motor but for my CC120 I don't have motor connectors.  Will I just pick these up at a bigger hobby shop?  The one close to me didn't have any that I saw, but heading to GA tomorrow.
Logged
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com

Offline Brandon Bartolomucci

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1007
Scorpion motor connectors
« Reply #1 on: January 02, 2013, 05:38:18 PM »
It's best to pick up the Castle Creations 6.5mm bullet connectors as I found out. WAY easier to solder together. You'll have to remove the existing ends from the motor but well worth it.


Regards,
Brandon Bartolomucci
Sent from my iPhone
Logged
Regards,
Brandon Bartolomucci
Team Synergy; Scorpion; & Bavarian Demon

Offline RichL

  • Synergy Veteran
  • *
  • Posts: 802
Re: Scorpion motor connectors
« Reply #2 on: January 02, 2013, 05:42:05 PM »
Quote from: inner3 on January 02, 2013, 05:35:30 PM
The male end is on the scorpion motor but for my CC120 I don't have motor connectors.  Will I just pick these up at a bigger hobby shop?  The one close to me didn't have any that I saw, but heading to GA tomorrow.
 

The connectors on the ends of the motor are banana plugs and should be removed anyway (per Matt).  This is not required but, standard bullet connectors make a better connection.  The stock Scorpion female connectors should have been included in the motor box none the less.

Rich
« Last Edit: January 02, 2013, 05:50:34 PM by RichL »
Logged
Synergy E5: Scorpion HKIII 4025-1100, CC ICE2 120HV, Rail 556/96, V-Bar Silverline

Synergy E7: Quantum 4530-500, CC ICE2 160HV, Rail 716/116, V-Bar Silverline

Offline RichL

  • Synergy Veteran
  • *
  • Posts: 802
Re: Scorpion motor connectors
« Reply #3 on: January 02, 2013, 05:51:45 PM »
Quote from: Brandon Bartolomucci on January 02, 2013, 05:38:18 PM
It's best to pick up the Castle Creations 6.5mm bullet connectors as I found out. WAY easier to solder together. You'll have to remove the existing ends from the motor but well worth it.


Regards,
Brandon Bartolomucci
Sent from my iPhone

+1

Rich
Logged
Synergy E5: Scorpion HKIII 4025-1100, CC ICE2 120HV, Rail 556/96, V-Bar Silverline

Synergy E7: Quantum 4530-500, CC ICE2 160HV, Rail 716/116, V-Bar Silverline

flyalan

  • Guest
Scorpion motor connectors
« Reply #4 on: January 02, 2013, 05:53:11 PM »
Suggest Castle bullets or if you use PRC 6 connectors those bullets work well also.

Cheers
Alan


Alan Butler
Team Synergy
Logged

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Re: Scorpion motor connectors
« Reply #5 on: January 02, 2013, 06:32:55 PM »
Oh, so I can just use some of the extra PRC6 bullets I have.  I ordered an extra set by accident but looks like it will be paying off.  That may be the solution just in case I don't find the CC bullets in store.  So then just put the female ends on the ESC and replace the male end with the male PRC6. 
Logged
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com

flyalan

  • Guest
Scorpion motor connectors
« Reply #6 on: January 02, 2013, 07:30:04 PM »
Quote from: inner3 on January 02, 2013, 06:32:55 PM
Oh, so I can just use some of the extra PRC6 bullets I have.  I ordered an extra set by accident but looks like it will be paying off.  That may be the solution just in case I don't find the CC bullets in store.  So then just put the female ends on the ESC and replace the male end with the male PRC6.
Works fine. Same style connector as the Castle 6.5mm. 

Alan


Alan Butler
Team Synergy
Logged

Offline wbefield

  • Member
  • **
  • Posts: 57
  • **
Re: Scorpion motor connectors
« Reply #7 on: January 13, 2013, 08:41:53 AM »
I ordered the CC 5.5mm connectors for my CC HV120 before I saw this thread.  Will they be big enough for those wires on the ESC motor wires?
Logged
Synergy N5C & E5-S
Rush
Protos 500
Mini Protos

Offline NKY Heli Guy

  • Full Member
  • ***
  • Posts: 164
Scorpion motor connectors
« Reply #8 on: January 13, 2013, 09:32:44 AM »
Yes I just put on 4mm yesterday with no issues.
Logged

Offline Jean-Luc Bolduc

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 614
Re: Scorpion motor connectors
« Reply #9 on: January 13, 2013, 05:15:17 PM »
EC5 bullits will do as well.
Logged
Team Synergy

Offline RichL

  • Synergy Veteran
  • *
  • Posts: 802
Re: Scorpion motor connectors
« Reply #10 on: January 13, 2013, 09:12:45 PM »
Quote from: wbefield on January 13, 2013, 08:41:53 AM
I ordered the CC 5.5mm connectors for my CC HV120 before I saw this thread.  Will they be big enough for those wires on the ESC motor wires?

Yes, they will work fine.

Rich
Logged
Synergy E5: Scorpion HKIII 4025-1100, CC ICE2 120HV, Rail 556/96, V-Bar Silverline

Synergy E7: Quantum 4530-500, CC ICE2 160HV, Rail 716/116, V-Bar Silverline

Offline wbefield

  • Member
  • **
  • Posts: 57
  • **
Re: Scorpion motor connectors
« Reply #11 on: January 13, 2013, 10:14:33 PM »
Thanks Rich
Logged
Synergy N5C & E5-S
Rush
Protos 500
Mini Protos

Offline RichL

  • Synergy Veteran
  • *
  • Posts: 802
Re: Scorpion motor connectors
« Reply #12 on: January 13, 2013, 10:18:21 PM »
No problem  ;D


Rich
Logged
Synergy E5: Scorpion HKIII 4025-1100, CC ICE2 120HV, Rail 556/96, V-Bar Silverline

Synergy E7: Quantum 4530-500, CC ICE2 160HV, Rail 716/116, V-Bar Silverline
Pages: [1]
« previous next »