Synergy Tech Support
Synergy Electric Helicopters => Synergy 516 => Topic started by: earlybird0513 on November 29, 2017, 01:27:34 PM
-
Just got my kit! I know I need the general hex wrenches 1.5-4mm, pitch gauge, Botos grease. What kind of thirty minute CA adhesive is good? What mm feathering wrench do I need for the head block? I’m using the the recommended electronics... scorpion motor, mks servos, and talon 90esc. What is the part number for the usb cord to program the talon? I’ve watched YouTube and read posts to get as much info for the tooling. If their is something I’ve missed any heads up would be appreciated. Thxs.
Sent from my iPhone using Tapatalk
-
do not forget, locktight, you will blue and red. 30 min, epoxy, or I use JB Weld for tail push rod.
-
Do you know the mm for the feathering wrench for the main head block?
Sent from my iPhone using Tapatalk
-
The spindle is 8mm.
+1 for JB Weld on the tail push rod.
-
Congrats on your new 516! It sounds like you are ready to jump right in. Take some time and read through the manual a couple times to familiarize yourself with the components and the assembly and you should be problem free. The head axle is 8mm. You will need some CA glue medium or thick to lock the screws down into the plastic rail for the battery tray slide. I recommend the use of JB Weld also for your tail assembly. The part needed for the Talon interface will either be the field programming unit or the castle link. http://www.castlecreations.com/en/accessories-5
Sent from my iPad using Tapatalk
-
Congrats on your new 516! It sounds like you are ready to jump right in. Take some time and read through the manual a couple times to familiarize yourself with the components and the assembly and you should be problem free. The head axle is 8mm. You will need some CA glue medium or thick to lock the screws down into the plastic rail for the battery tray slide. I recommend the use of JB Weld also for your tail assembly. The part needed for the Talon interface will either be the field programming unit or the castle link. http://www.castlecreations.com/en/accessories-5
Sent from my iPad using Tapatalk
Thanks so much everybody! I’ve been reading the manual everyday for the last month. I think I’m obsessed. I’m happy with all the support, thxs.
Sent from my iPhone using Tapatalk
-
Obsessed? Yeah,none of us have any idea what you're talking about... Lol! Welcome to the Synergy family and enjoy!
-
Nope, no obsessives here.
+1 for jb weld to assemble the tail pushrod.
Enjoy your build
Sent from my SM-G930F using Tapatalk
-
Nope, no obsessives here.
+1 for jb weld to assemble the tail pushrod.
Enjoy your build
Sent from my SM-G930F using Tapatalk
When use Jb weld make sure to tape them till it dries, they will try to slide off. Leave over night they will never pull off. Soap threads easier to thead links on. Cliff
Sent from my SM-T550 using Tapatalk
-
When use Jb weld make sure to tape them till it dries, they will try to slide off. Leave over night they will never pull off. Soap threads easier to thead links on. Cliff
I just make sure that there's constant compression on the assembly while it cures. I'll usually mount the rod to one of its endpoints on the heli and then press the other end against something.
-
do not forget, locktight, you will blue and red. 30 min, epoxy, or I use JB Weld for tail push rod.
Check thank you .
Sent from my iPhone using Tapatalk
-
Congrats on your new 516! It sounds like you are ready to jump right in. Take some time and read through the manual a couple times to familiarize yourself with the components and the assembly and you should be problem free. The head axle is 8mm. You will need some CA glue medium or thick to lock the screws down into the plastic rail for the battery tray slide. I recommend the use of JB Weld also for your tail assembly. The part needed for the Talon interface will either be the field programming unit or the castle link. http://www.castlecreations.com/en/accessories-5
Sent from my iPad using Tapatalk
Thank you
Sent from my iPhone using Tapatalk
-
Obsessed? Yeah,none of us have any idea what you're talking about... Lol! Welcome to the Synergy family and enjoy!
Sent from my iPhone using Tapatalk
-
I’m all done with bind and fly! First build kit!
Sent from my iPhone using Tapatalk
-
Obsessed? Yeah,none of us have any idea what you're talking about... Lol! Welcome to the Synergy family and enjoy!
I know I'm not. lol
-
I’m all done with bind and fly! First build kit!
Sent from my iPhone using Tapatalk
Congratulations! Be sure to share photos.
-
I’m all done with bind and fly! First build kit!
Sent from my iPhone using Tapatalk
Congratulations! Be sure to share photos.
You betcha!
Sent from my iPhone using Tapatalk