November 25, 2024, 07:08:03 PM
« previous next »
Pages: [1]

Author Topic: Servo Set-up Tips  (Read 3341 times)

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Servo Set-up Tips
« on: January 02, 2013, 06:29:05 PM »
I have a question to ask, but because I keep opening new threads I would like others to post there tips for future readers.  But first my question.

I tried to get my CC120 and BEC soldered today but the LHS could not get it in the PRC6 connector.  He was just having a really bad day and after an hour and a half, I didn't want to take a chance on him screwing something up.  I still want to set my servos to center and program my Vbar tonight or tomorrow morning though.  Here is my idea:
I have an esc from a 400 that isn't being used and a 3S battery that plugs into it.  Just for set up purposes, would it be ok to plug that into Vbar so I can get things setup?  I will not plug the motor in, just the speed controller into Vbar and the servos and AR8000.  But I wanted to check before I did something bad.  Hope to hear YES, but if there will be problems let me know.
Oh yeah, I am using the BLS255/256 combo.
Logged
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com

Offline RichL

  • Synergy Veteran
  • *
  • Posts: 802
Re: Servo Set-up Tips
« Reply #1 on: January 02, 2013, 06:35:12 PM »
As long as the out put voltage from the on board BEC is at or below 2S the Vbar will be fine.  You could use a NiCD or Life battery to accomplish the same thing.  One other caution with the Vbar, make sure that your sensor it plugged in correctly if you reverse the polarity it's finished.

Rich
Logged
Synergy E5: Scorpion HKIII 4025-1100, CC ICE2 120HV, Rail 556/96, V-Bar Silverline

Synergy E7: Quantum 4530-500, CC ICE2 160HV, Rail 716/116, V-Bar Silverline

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Re: Servo Set-up Tips
« Reply #2 on: January 02, 2013, 06:38:03 PM »
Which sensor?
Logged
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Re: Servo Set-up Tips
« Reply #3 on: January 02, 2013, 06:39:17 PM »
Also, how would I plug it in with a NiCd?  Oh well, don't have one I was thinking about one of my car packs but that is NiMh
Logged
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Re: Servo Set-up Tips
« Reply #4 on: January 02, 2013, 06:41:12 PM »
Hmmm, I think you mean the Vbar sensor, guess I thought you meant a telemtry sensor or something.  So just make sure I have positive to positive and negative to negative.  Or do you mean the servo type plugs that go into the vbar?  Just making sure so I don't destroy something.  Glad I'm asking.
Logged
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com

Offline RichL

  • Synergy Veteran
  • *
  • Posts: 802
Re: Servo Set-up Tips
« Reply #5 on: January 02, 2013, 07:14:50 PM »
Quote from: inner3 on January 02, 2013, 06:41:12 PM
Hmmm, I think you mean the Vbar sensor, guess I thought you meant a telemtry sensor or something.  So just make sure I have positive to positive and negative to negative.  Or do you mean the servo type plugs that go into the vbar?  Just making sure so I don't destroy something.  Glad I'm asking.

Ok, we are on the same page now.  Since you are using the V-Bar Mini you don't have and external (gyro) sensor (the one to which I was referring).

Rich
« Last Edit: January 02, 2013, 09:44:17 PM by RichL »
Logged
Synergy E5: Scorpion HKIII 4025-1100, CC ICE2 120HV, Rail 556/96, V-Bar Silverline

Synergy E7: Quantum 4530-500, CC ICE2 160HV, Rail 716/116, V-Bar Silverline

Offline BrianE

  • Field Representative
  • Full Member
  • ****
  • Posts: 191
Re: Servo Set-up Tips
« Reply #6 on: January 02, 2013, 07:46:22 PM »
Wait a minute - I'm a bit of a Johnny-come-lately here, but are you planning on using an AR8000?  You only need a couple of remote receivers instead - that'll clean up a rats best of wires for ya.
Logged
E7SE, Sliverline VBar, Edge 160HVf, Scorpion HKIII 4530, Futaba BLS, OptiGuard and BEC Guards

E5-626, Vbar NEO, Edge 120HV, Scorpion HKIII 4035, MKS 950/980 OptiGuard and BEC Guards

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Re: Servo Set-up Tips
« Reply #7 on: January 02, 2013, 10:45:14 PM »
Yeah I know, but I have this receiver sitting around and want to use it so I can have it in a bird.  I have used Sats before, but going to use the receiver this time.  Also like the telemetry I have with it.
Logged
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Re: Servo Set-up Tips
« Reply #8 on: January 02, 2013, 11:30:16 PM »
Didn't work.
Logged
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com

Offline RichL

  • Synergy Veteran
  • *
  • Posts: 802
Re: Servo Set-up Tips
« Reply #9 on: January 02, 2013, 11:42:34 PM »
What didn't work?

Rich
Logged
Synergy E5: Scorpion HKIII 4025-1100, CC ICE2 120HV, Rail 556/96, V-Bar Silverline

Synergy E7: Quantum 4530-500, CC ICE2 160HV, Rail 716/116, V-Bar Silverline

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Re: Servo Set-up Tips
« Reply #10 on: January 03, 2013, 01:15:06 AM »
The Vbar wouldn't get power from the crappo walkera esc.  I'm sure the wire they had was mislabeled or not the right one. I've never used if before.
Logged
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Re: Servo Set-up Tips
« Reply #11 on: January 03, 2013, 01:55:59 AM »
Just thought of it, should have hooked the esc to the receiver first, then to Vbar.  I'll try in the morning.
Logged
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com

Offline RichL

  • Synergy Veteran
  • *
  • Posts: 802
Re: Servo Set-up Tips
« Reply #12 on: January 03, 2013, 02:40:36 AM »
Don't worry about it too much we will get it straightened out tomorrow.

Rich
Logged
Synergy E5: Scorpion HKIII 4025-1100, CC ICE2 120HV, Rail 556/96, V-Bar Silverline

Synergy E7: Quantum 4530-500, CC ICE2 160HV, Rail 716/116, V-Bar Silverline

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Re: Servo Set-up Tips
« Reply #13 on: January 03, 2013, 10:05:27 AM »
Sounds good.  My wife needs to hurry up and get ready so I can take her to get her car and then I can get on the road. 
Logged
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com
Pages: [1]
« previous next »