November 22, 2024, 08:03:24 PM
« previous next »
Pages: [1]

Author Topic: Bench electrical set up power source?  (Read 3233 times)

Offline Barry Tilson

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 617
  • Perspective Visuals
Bench electrical set up power source?
« on: January 27, 2013, 03:20:05 PM »
What does everyone use for setting up electronics on the bench? I'm hearing that it's not good to use the BEC in your ESC.  Bls 251 and 253 are not high voltage 2s compatible correct. So I need a BEC for the bench or a life pack at 6v?


Sent from my iPad using Tapatalk HD
Logged
Perspective Visuals

Offline Anthony Oxlade

  • Full Member
  • ***
  • Posts: 122
Re: Bench electrical set up power source?
« Reply #1 on: January 27, 2013, 03:28:54 PM »
I usually perform bench setup with either my BEC or scorpion backup guard (if only a quick tweak is necessary). I also have a 1600mAh 6V nimh in my toolbox which i can temporarily plug into the vbar control unit to power the system.

To prevent accidental spool up, you should disconnect two motor leads if using the BEC in your ESC.
Logged
Synergy E7 - 4525 Ultimate, 8917HV, HBL980, Vbar Silverline, HW 120HV, Quasar 7075 BEC, Edge 693/115
Synergy E7 - 4525 Ultimate, 8717HV, HBL980, Vbar Silverline, Scorpion 130A, HV2 BEC, Rail 696/116

Offline Chris Sexton

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2729
  • Admiral, There be whales here!
Bench electrical set up power source?
« Reply #2 on: January 27, 2013, 03:35:32 PM »
I have a 6.6v NiMH rx pack I keep around for initial setups and tuning. I don't like like having the esc powered up when I can help it.

As for setups with BECs, once the bec is set to the right voltage there is no reason I can think of not to use it. Assuming its an external BEC that is.
Logged
Chris Sexton
Synergy Factory Specialist / Rail Blades / Team Scorpion

Offline Barry Tilson

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 617
  • Perspective Visuals
Bench electrical set up power source?
« Reply #3 on: January 27, 2013, 03:55:38 PM »
Do you think the Kontronik 120 HV  needs a backup guard using the internal BEC?


Sent from my iPhone using Tapatalk
Logged
Perspective Visuals

Offline Chris Sexton

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2729
  • Admiral, There be whales here!
Bench electrical set up power source?
« Reply #4 on: January 27, 2013, 04:03:32 PM »
The Jive BEC is one if the best LV BeCs around. But for what a backup guard costs, I would still run one. Cheap insurance.
Logged
Chris Sexton
Synergy Factory Specialist / Rail Blades / Team Scorpion

flyalan

  • Guest
Bench electrical set up power source?
« Reply #5 on: January 27, 2013, 05:31:54 PM »
I've started using backup guards. They are very handy.  I also have a Nimh receiver pack and switch for sit-ups.

Alan

Logged

Offline Barry Tilson

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 617
  • Perspective Visuals
Bench electrical set up power source?
« Reply #6 on: January 27, 2013, 08:01:38 PM »
Just ordered a receiver pack. Will have to look into the back up guard.


Sent from my iPhone using Tapatalk
Logged
Perspective Visuals

Offline RichH

  • Newbie
  • *
  • Posts: 45
Bench electrical set up power source?
« Reply #7 on: January 31, 2013, 08:57:51 PM »
I've modified a balance cable extension to just pull off power from two cells on a flight pack.


Rich
« Last Edit: January 31, 2013, 09:21:12 PM by RichH »
Logged

Offline Barry Tilson

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 617
  • Perspective Visuals
Bench electrical set up power source?
« Reply #8 on: February 01, 2013, 06:18:22 AM »
Not sure if I can do that I think the BLS251 is low volt 4.8v and the BLS253's are 6.0v.

My Kontronik is probably set for 5.6v from what I've read.

Do I need a regulator for the tail? I was putting 6.6v from the reciver pack I picked up for the setup.  Lucky I didn't charge it up to it full charge at 7.2v before using it for set up.

Looks like lot of people on the fourms are using the BLS251 at a regulated 6.0v without reported troubles. Seems counter productive not to follow the spec even if it seems to work?
Logged
Perspective Visuals

Offline Chris Sexton

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2729
  • Admiral, There be whales here!
Bench electrical set up power source?
« Reply #9 on: February 01, 2013, 07:02:24 AM »
Leave the bec at 5.6v and run. The tail servo specs are old. It will handle 6v. Hundreds I pilots including myself run them this way no issues.
Logged
Chris Sexton
Synergy Factory Specialist / Rail Blades / Team Scorpion

Offline Barry Tilson

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 617
  • Perspective Visuals
Bench electrical set up power source?
« Reply #10 on: February 01, 2013, 07:28:39 AM »
What about the life PAC? Just discharge it below 6.0v?


Logged
Perspective Visuals

Offline Chris Sexton

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2729
  • Admiral, There be whales here!
Re: Bench electrical set up power source?
« Reply #11 on: February 01, 2013, 08:14:52 AM »
I don't have any personal experience with the backup back used with Jive. I think it is a NiMH pack and it stays charged to 5.6v by the BEC and if the BEC fails the battery is already in parallel to take over.

I would check out the Kontronic forms on HF or RR to get clarification on that.
Logged
Chris Sexton
Synergy Factory Specialist / Rail Blades / Team Scorpion

Offline Barry Tilson

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 617
  • Perspective Visuals
Bench electrical set up power source?
« Reply #12 on: February 01, 2013, 08:27:01 AM »
Sorry the pac is just for set up on the bench. I will just discharge it a bit. I already put 6.6v to the BLS251. Pretty sure there is t any load on the bench.


Sent from my iPhone using Tapatalk
Logged
Perspective Visuals

Offline Chris Sexton

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2729
  • Admiral, There be whales here!
Re: Bench electrical set up power source?
« Reply #13 on: February 01, 2013, 08:53:48 AM »
Quote from: PerspectiveVisuals on February 01, 2013, 08:27:01 AM
Sorry the pac is just for set up on the bench. I will just discharge it a bit. I already put 6.6v to the BLS251. Pretty sure there is t any load on the bench.


Sent from my iPhone using Tapatalk

Yeah it's fine :)
Logged
Chris Sexton
Synergy Factory Specialist / Rail Blades / Team Scorpion
Pages: [1]
« previous next »