November 01, 2024, 01:22:27 AM

Author Topic: My Nitro N7 Spec  (Read 3171 times)

Offline JamesGreen

  • Member
  • **
  • Posts: 66
My Nitro N7 Spec
« on: November 04, 2015, 03:08:45 PM »
Hi all,

Thought I'd post my N7 spec and a few pictures:

OS105HZ & Powerboost Pipe
Futaba BLS275SV Cyclics
Futaba BLS276SV Tail
Futaba BLS272SV Throttle
Rail 693mm & 106mm blades
Vbar NEO & Vbar Control
Align governor sensor
Optipower 2S 2150mah Lipo (going to get a bigger one)
Perfect regulators Safe Switch 2
Gryphon pin switch
Gryphon mini auto booster
Optifuel fuel 20%

Loving this Heli. :)
« Last Edit: November 05, 2015, 01:36:01 AM by JamesGreen »

Offline Cliff Chmiel

  • Synergy Veteran
  • *
  • Posts: 588
  • Cliff
Re: My Nitro N7 Spec
« Reply #1 on: November 04, 2015, 03:18:18 PM »
Nice
Cliff

Offline Roger

  • Full Member
  • ***
  • Posts: 221
Re: My Nitro N7 Spec
« Reply #2 on: November 04, 2015, 03:51:26 PM »
Nice looking build James.  How are you liking the NEO on this machine?  Is the NEO seeing any Extreme Vibes?  Are you running the Rescue feature in the NEO and if so how did it work for you.  I have NEO and Vcontrol for my N7 and have not yet tried the Rescue on it.  I am seeing some extreme vibes being logged by the system. 

ROG
ROG
Retired Old Guy

Offline Mike Spano

  • Synergy Hero
  • **
  • Posts: 1038
Re: My Nitro N7 Spec
« Reply #3 on: November 04, 2015, 04:04:31 PM »
not to hijack or interfere here, but my neo is rocking its butt off on my N7!!! loving it. no extreme vibs unless I am flying hard, the I can show extreme vibs on my E7SE at that point too. the rescue feature works flawlessly with it also. it may go up at a 10degree angle instead of perfectly straight, but it works none the less. IMHO the neo flys twice as good as the silver line did...
Team Synergy
Rail Blades
TRM Power
Team Byron Fuels
MKS Servos

Offline Rodney Kirstine

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 2112
Re: My Nitro N7 Spec
« Reply #4 on: November 04, 2015, 04:39:07 PM »
So clean! :D
Rodney

Team Synergy

Offline JamesGreen

  • Member
  • **
  • Posts: 66
My Nitro N7 Spec
« Reply #5 on: November 04, 2015, 04:58:03 PM »
Hi Roger, NEO is running great. I'm not using rescue, but using Pro. I have found the NEO to be more solid in fast forward flight (no pitching up tendency)

I have just checked my logs and I have only seen a couple of extreme vibe log entries (1 or 2 during a 6-7min flight), which I think is normal to see depending the manoeuvre. Recently moving from electric to nitro, I thought I would have some vibe issues, but really surprised at how smooth it is.

I also like the OS105hz, I used to use the regulated version, but the hz, from my perspective is easier.

For info I'm running the following settings: (after following standard setup).

Main Rotor

Expo 10
Style 80
Agility 120
Gain 75
Pitch 13deg

Tail

Expo 50
Rate 130 (overdrive enabled)
Gain 75

Governor

2000rpm
Gain 60

I mounted the NEO in the normal position with wiring all underneath the battery plate, to keep it nice and neat. For the antennas, I used some standard rx tubing, one running straight down the side of the frame, one I heated up with and bent 90deg (I put a length of solder in the middle whilst doing it to ensure the hole didn't close up). I also put some clunk tubing over the wires for protection.

My safe switch is also underneath the battery plate.
« Last Edit: November 04, 2015, 05:29:04 PM by JamesGreen »

Offline cml001

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 684
Re: My Nitro N7 Spec
« Reply #6 on: November 04, 2015, 05:07:13 PM »
Sweet!
Clay
I can fly helicopters... Upside down!

Offline Ross Lawton

  • Factory Specialist
  • Synergy Veteran
  • *****
  • Posts: 793
Re: My Nitro N7 Spec
« Reply #7 on: November 05, 2015, 03:10:09 AM »
Nice setup and clean install James. 8)

Cheers,
Ross
Team Synergy - UK