November 22, 2024, 02:26:05 AM

Author Topic: What governor sensor/bracket to use  (Read 2948 times)

Offline troasb

  • Full Member
  • ***
  • Posts: 144
What governor sensor/bracket to use
« on: September 24, 2015, 05:49:49 AM »
I initially installed an Align sensor and magnets. But I found it difficult to properly fix the Align bracket to the N7's bracket. I ended up using just one srew and that was not good enough, so no it is ruined. Do you folks know about another sensor/magnet that is easy to install on the N/

Trond
Norway

Offline GAR

  • Newbie
  • *
  • Posts: 24
Re: What governor sensor/bracket to use
« Reply #1 on: September 24, 2015, 06:24:01 AM »
No magnet needed here. I like revlimiting the motor over the head... if you could do both?

KDE Direct backplate sensor bracket and Spektrum RevLimit Sensor.

It works for me.

Offline cml001

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 684
Re: What governor sensor/bracket to use
« Reply #2 on: September 24, 2015, 11:28:09 AM »
I actually use both on the N5C... Align magnet sensor on the clutch bell for the iKon gov & the KDE/Spektrum backplate for the telemetry unit. Works well.
Clay
I can fly helicopters... Upside down!

Offline troasb

  • Full Member
  • ***
  • Posts: 144
Re: What governor sensor/bracket to use
« Reply #3 on: September 24, 2015, 01:36:45 PM »
Thank you guys, but none of this really helps me. I have an Align sensor (to Ikon) that does not fit very well. I am wondering if anybody know another type that fits the bracket in the N7 better.

Offline cml001

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 684
Re: What governor sensor/bracket to use
« Reply #4 on: September 24, 2015, 05:41:58 PM »
That should be a plug'n'play fit.
Clay
I can fly helicopters... Upside down!

Offline Ben Kerr

  • Field Representative
  • Sr. Member
  • ****
  • Posts: 307
Re: What governor sensor/bracket to use
« Reply #5 on: September 25, 2015, 09:50:07 PM »
Thank you guys, but none of this really helps me. I have an Align sensor (to Ikon) that does not fit very well. I am wondering if anybody know another type that fits the bracket in the N7 better.

I use the futaba sensor and it bolts right up.
Team Synergy / Rail Blades / Scorpion Power Systems/Thunder Power

Offline Danny Dugger

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 636
Re: What governor sensor/bracket to use
« Reply #6 on: September 26, 2015, 09:15:20 AM »
I'm a little confused, how is the Align sensor not fitting properly on your machine? It is a popular choice and should fit perfectly.

Offline troasb

  • Full Member
  • ***
  • Posts: 144
Re: What governor sensor/bracket to use
« Reply #7 on: September 26, 2015, 01:02:48 PM »
Thank you Danny for useful pictures, but like me you have only been able to fix it with one screw and then it easily comes loose. But you have done it a little different than me, I'll use your pictures as a guideline here.

Offline Danny Dugger

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 636
Re: What governor sensor/bracket to use
« Reply #8 on: September 26, 2015, 06:55:44 PM »
Use a nut with loctite. This part is not under any stress so the one bolt will hold it fine, you just need some loctite to secure it from vibration. No problem! That sensor has held on through a couple crashes and never moved.

Offline Roger

  • Full Member
  • ***
  • Posts: 221
Re: What governor sensor/bracket to use
« Reply #9 on: October 26, 2015, 04:34:03 PM »
I use the baseplate sensor from Spektrum on my N7.  It works very well with my OS .91 HZ F3C Speed motor and the Neo FBL controller.  Easy Peasy install.

ROG
ROG
Retired Old Guy

Offline Drew Robinson

  • Full Member
  • ***
  • Posts: 183
Re: What governor sensor/bracket to use
« Reply #10 on: March 05, 2016, 07:45:57 PM »
Depending on fbl unit, vbar use spectrum backplate, cgy750
Use the futab bps-1. Both have been incredibly accurate for me!
**Team Synergy**Team Scorpion**

Offline Gabriel Sandoval

  • Field Representative
  • Sr. Member
  • ****
  • Posts: 322
  • If your not crashin' your not trying hard enough..
    • Midwest Heli Boyz
Re: What governor sensor/bracket to use
« Reply #11 on: March 24, 2016, 10:16:40 AM »
I use the Align sensor with a single bolt with lockwasher and loctite. Multiple gallons through the birds and it has not moved a bit.

Gabe
Team Synergy
Team Scorpion
Team Dee Force Aviation
Team YS Performance USA
Looking for a fuel Sponsor