November 23, 2024, 02:20:04 AM
« previous next »
Pages: [1]

Author Topic: Rail Blades tail blades  (Read 6620 times)

Offline AlanzoNembhard

  • Member
  • **
  • Posts: 50
Rail Blades tail blades
« on: September 27, 2011, 08:02:18 PM »
Hey Guy Just Saw this on runryder so i have to upgrade my tail unit to the 6mm shaft and hub to run the new rail tail blade since they are 96mm and old system is rated for 92mm tail blade
Logged

Offline steffgiguere

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1373
Re: Rail Blades tail blades
« Reply #1 on: September 27, 2011, 08:34:21 PM »
That is right.
Logged
Team Synergy, Canada

Offline AlanzoNembhard

  • Member
  • **
  • Posts: 50
Re: Rail Blades tail blades
« Reply #2 on: September 27, 2011, 08:57:14 PM »
Well if that case they to come out with 92 mm rail blade for the original n5 lets hear what matt has to say first because i like my main and tail blade match
Logged

Offline Matt Botos

  • Synergy Hero
  • **
  • Posts: 1573
    • Matt Botos
Re: Rail Blades tail blades
« Reply #3 on: September 27, 2011, 10:20:19 PM »
Yeah, if you want to run the 96mm tail blades you will have to upgrade your tail assembly. I dont have any immediate plans on releasing 92mm tail blades. Sorry.
However, you will be very happy with the new tail system. Much less susceptible to resonance and take a beating way better.

Matt
Logged

Offline AlanzoNembhard

  • Member
  • **
  • Posts: 50
Re: Rail Blades tail blades
« Reply #4 on: September 27, 2011, 10:22:13 PM »
can you list the part i need to run the new tail blade matt
Logged

Offline Yanick Larouche

  • Field Representative
  • Sr. Member
  • ****
  • Posts: 434
Re: Rail Blades tail blades
« Reply #5 on: September 27, 2011, 10:38:27 PM »
Hi Alanzo !

You need this parts for run the new tail.

6mm Tail Output Shaft                                    N5c-615-124
6x13x5 Flange Bearing                                    N5c-108-616
9T Tail Pulley(6mm shaft)                                N5c-615-314
CF Tail Box Plate                                             N5c-615-313
CF Vertical Fin                                                 N5c-615-136
HD Tail Blade Grip                                           N5c-515-525
HD Tail Rotor Hub (for 6mm shaft)                   N5c-615-324
Tail Pitch Slider Bushing(for 6mm shaft)           N5c-615-319

Thank's !

Yan
 ;)

Logged
Team Synergy

Offline AlanzoNembhard

  • Member
  • **
  • Posts: 50
Re: Rail Blades tail blades
« Reply #6 on: September 28, 2011, 09:41:48 AM »
Dam that alot of money that almost a new n5c kit if i did that and the new frame i wish come up with a upgrade for these thing
Logged

Offline Jerry Kovar

  • Full Member
  • ***
  • Posts: 173
Re: Rail Blades tail blades
« Reply #7 on: September 28, 2011, 03:52:01 PM »
You are talking a little over 100$ us for that upgrade... a lot cheaper than a whole new kit... for comparison.   If you where going to upgrade a comparable machine with new KDE and the components listed, you would be way over the 100$ mark....  not including blades on either...   thats just for the tail... not sure what the totals would be if you try to re-kit for a whole new n5c...


might be better for you to purchase a new n5c kit, and have your N5 (the parts that are comparable) as a back up..



best of luck..




« Last Edit: September 28, 2011, 03:53:34 PM by Jerry Kovar »
Logged
Team Synergy

Offline Tommy Wagner

  • Field Representative
  • Sr. Member
  • ****
  • Posts: 418
Rail Blades tail blades
« Reply #8 on: September 30, 2011, 04:53:41 PM »
I just measured my rail tail blades and in a straight line from hole to tip they are 92.50 and from hole to tip diagonaly 96.00 can we use these on a N5 with out problems?  The plastic ones that came with the kit are 92.92 straight and 93.50 diagonally. Is there that much difference?
« Last Edit: September 30, 2011, 04:59:31 PM by Tommy Wagner »
Logged

Offline p johnston

  • Field Representative
  • Member
  • ****
  • Posts: 55
Re: Rail Blades tail blades
« Reply #9 on: September 30, 2011, 05:16:04 PM »
Do not use the Rail tail blades on the original tail hub. That little difference spinning 10000 rpm is a big difference.
Right now on my N5, I use the Radix 92 blades. Works very well. 8)
Logged

Offline steffgiguere

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1373
Re: Rail Blades tail blades
« Reply #10 on: September 30, 2011, 05:17:42 PM »
Exactly which one are they? KBDD, Edge, Cy etc...
Logged
Team Synergy, Canada

Offline p johnston

  • Field Representative
  • Member
  • ****
  • Posts: 55
Re: Rail Blades tail blades
« Reply #11 on: September 30, 2011, 05:24:12 PM »
I will add that its not only about length. The cord width is more as well. Just a lot more area on the blade over the stock and other 95-96 blades out their.
Logged
Pages: [1]
« previous next »