Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email
?
Home
Help
Search
Login
Register
November 01, 2024, 01:32:12 AM
Synergy Tech Support
»
Synergy Electric Helicopters
»
Synergy E7SE
»
What tails are you using
« previous
next »
Print
Pages: [
1
]
Author
Topic: What tails are you using (Read 4016 times)
steffgiguere
Field Representative
Synergy Hero
Posts: 1373
What tails are you using
«
on:
September 16, 2011, 04:07:37 PM »
If I remember well Matt was using 96mm Rails on his E7 at IRCHA, is this correct....would 105 be to long?
Logged
Team Synergy, Canada
Matt Botos
Synergy Hero
Posts: 1573
Re: What tails are you using
«
Reply #1 on:
September 16, 2011, 06:53:24 PM »
95's do not work very well on the E7, they end up traveling too far and stalling the tail blades which in turn causes skipping teeth on the belt.
Here is what you should run -
E7 - 105 - 110mm
E6 - 95 - 105
Thanks,
Matt
Logged
steffgiguere
Field Representative
Synergy Hero
Posts: 1373
Re: What tails are you using
«
Reply #2 on:
September 16, 2011, 07:39:30 PM »
Thanks Matt.
Logged
Team Synergy, Canada
seldred
Sr. Member
Posts: 327
Re: What tails are you using
«
Reply #3 on:
September 16, 2011, 07:59:33 PM »
I have a set of 110mm tails for my E7 just until I can get my rail 106mm blades in. I would recommend trying the 105/106mm size first and see what you think.
Logged
Matt Botos
Synergy Hero
Posts: 1573
Re: What tails are you using
«
Reply #4 on:
September 16, 2011, 08:04:55 PM »
The 106 Rails work very well.... I dont see needing anymore than that with a 4.66:1 tail ratio.
Matt
Logged
Chris Sexton
Factory Specialist
Synergy Hero
Posts: 2729
Admiral, There be whales here!
Re: What tails are you using
«
Reply #5 on:
September 23, 2011, 12:15:22 AM »
I am planning to purchase a set of Rail tail blades when the the Rail 693 Mains become available. For my maiden flight, I put EDGE FBL 693 Mains and EDGE 115 CF tail blades.
115 is almost too long. The tail blades are VERY close to the ground. The tail fin is still longer but only slightly.
Logged
Chris Sexton
Synergy Factory Specialist / Rail Blades / Team Scorpion
Matt Botos
Synergy Hero
Posts: 1573
Re: What tails are you using
«
Reply #6 on:
September 23, 2011, 10:47:54 AM »
115's are huge for this helicopter, especially with a 4.66:1 tail ratio.
Guys that are using 115's are usually trying to compensate for a slower tail such as Trex700.
Thanks,
Matt
Logged
Chris Sexton
Factory Specialist
Synergy Hero
Posts: 2729
Admiral, There be whales here!
Re: What tails are you using
«
Reply #7 on:
September 23, 2011, 11:05:47 AM »
yeah I will be swapping the 115s for the Rails when they become available
«
Last Edit: September 23, 2011, 11:11:40 AM by cdsexton
»
Logged
Chris Sexton
Synergy Factory Specialist / Rail Blades / Team Scorpion
skyfoxsxer
Newbie
Posts: 6
Re: What tails are you using
«
Reply #8 on:
September 28, 2011, 03:22:29 PM »
Can 105's clear on a E6 swinging 625mm mains?
Logged
Matt Botos
Synergy Hero
Posts: 1573
Re: What tails are you using
«
Reply #9 on:
September 28, 2011, 05:57:31 PM »
I think they would clear just fine. The E6 can actually swing 630mm main blades.
Matt
Logged
Print
Pages: [
1
]
« previous
next »
Synergy Tech Support
»
Synergy Electric Helicopters
»
Synergy E7SE
»
What tails are you using