Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email
?
Home
Help
Search
Login
Register
October 31, 2024, 06:44:37 PM
Synergy Tech Support
»
Synergy Electric Helicopters
»
Synergy E7SE
»
8mm Pinions
« previous
next »
Print
Pages: [
1
]
Author
Topic: 8mm Pinions (Read 1794 times)
mahbouni
Newbie
Posts: 7
8mm Pinions
«
on:
November 22, 2012, 03:50:43 PM »
Are there any plans to produce pinions with 8mm bore so we can try the Pyro 800-48?
Logged
Chris Sexton
Factory Specialist
Synergy Hero
Posts: 2729
Admiral, There be whales here!
8mm Pinions
«
Reply #1 on:
November 22, 2012, 04:06:01 PM »
I don't think the pyro 800 fits between the frames. Frame width is 60mm isn't it?
Sent from my iPhone using Tapatalk
Logged
Chris Sexton
Synergy Factory Specialist / Rail Blades / Team Scorpion
Jean-Luc Bolduc
Field Representative
Synergy Veteran
Posts: 614
Re: 8mm Pinions
«
Reply #2 on:
November 22, 2012, 08:54:55 PM »
62 mm spacing, but 800 is 63mm. You'd have to put washers or spacers to widen frames to make it fit.
Logged
Team Synergy
Jean-Luc Bolduc
Field Representative
Synergy Veteran
Posts: 614
Re: 8mm Pinions
«
Reply #3 on:
November 22, 2012, 08:56:11 PM »
Pinions could be drilled a bit, not sure if ok to enlarge hole from 6mm to 8mm.
Logged
Team Synergy
Chris Sexton
Factory Specialist
Synergy Hero
Posts: 2729
Admiral, There be whales here!
8mm Pinions
«
Reply #4 on:
November 22, 2012, 09:13:42 PM »
Quote from: 4cyclic on November 22, 2012, 08:54:55 PM
62 mm spacing, but 800 is 63mm. You'd have to put washers or spacers to widen frames to make it fit.
Ahh I was reading the spot for max motor on a different thread. Thanks for the clarification.
Sent from my iPhone using Tapatalk
Logged
Chris Sexton
Synergy Factory Specialist / Rail Blades / Team Scorpion
Jean-Luc Bolduc
Field Representative
Synergy Veteran
Posts: 614
Re: 8mm Pinions
«
Reply #5 on:
November 23, 2012, 07:55:13 PM »
it's a really nice motor, no doubt. Keep us posted if you decide to go and do the trial.
Logged
Team Synergy
mahbouni
Newbie
Posts: 7
Re: 8mm Pinions
«
Reply #6 on:
November 24, 2012, 06:24:49 AM »
If the motor is too wide then I'm not going to mod anything. Was just wondering if it will work. There is a Pyro 750 being tested by some pilots over here.
Logged
Matt Botos
Synergy Hero
Posts: 1573
Re: 8mm Pinions
«
Reply #7 on:
December 16, 2012, 12:56:40 PM »
The Pyro 750 would be a better option! It will have more than enough power for the E7.
Logged
Print
Pages: [
1
]
« previous
next »
Synergy Tech Support
»
Synergy Electric Helicopters
»
Synergy E7SE
»
8mm Pinions