November 23, 2024, 01:00:07 AM
« previous next »
Pages: [1] 2

Author Topic: Bell Crank Assembly  (Read 3940 times)

Offline Chris McClard

  • Newbie
  • *
  • Posts: 27
Bell Crank Assembly
« on: January 09, 2013, 04:27:03 PM »
Ok this is going to be a no brainer question here. Once the bell crank is all put together the outside bells should rotate freely correct? One of mine has a notchy feeling when I tighten up the bolt. I'm assuming this is a bad bearing. 
« Last Edit: January 10, 2013, 02:22:20 AM by 3Dflyen »
Logged
Chris McClard
Fly It Like You Hate It!!!
Synergy N9, Synergy N5c, Synergy 516, Goblin 700, Trex 600E Trex 500 Pro, Trex 250 Pro, Raptor 50, MD 500E with Trex 500 guts, Beam E4.

Offline Chris Sexton

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2729
  • Admiral, There be whales here!
Re: Bell Crank Assembly
« Reply #1 on: January 10, 2013, 07:44:35 AM »
Yes, with no links installed they should flop around pretty good. You might have a bad bearing or something aligned right. Maybe a shim in the wrong/missing place?
Logged
Chris Sexton
Synergy Factory Specialist / Rail Blades / Team Scorpion

Offline Brandon Bartolomucci

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1007
Bell Crank Assembly
« Reply #2 on: January 10, 2013, 07:53:02 AM »
The bell cranks are a bit tricky to get aligned just right but as Chris mentioned they should spin freely. I would try loosening the set screw a hair and moving the rod between the frames just a wee bit and see if that helps.


Regards,
Brandon Bartolomucci
Sent from my iPhone
Logged
Regards,
Brandon Bartolomucci
Team Synergy; Scorpion; & Bavarian Demon

Offline JeepCJ

  • Full Member
  • ***
  • Posts: 117
Bell Crank Assembly
« Reply #3 on: January 10, 2013, 10:32:36 AM »
I would pull the bearings out and see how they feel, that way you know for sure if the issue is a bad bearing, or need to look elsewhere in the setup for the cause. 

Bob
Logged
Bob Fisk
Team Synergy
Central NY

Offline Chris McClard

  • Newbie
  • *
  • Posts: 27
Re: Bell Crank Assembly
« Reply #4 on: January 10, 2013, 03:53:33 PM »
I found some other bearing from my N9 that I replaced a while back and it was a lot better but could tell they was old so I ordered a set just to be on the safe side.
Logged
Chris McClard
Fly It Like You Hate It!!!
Synergy N9, Synergy N5c, Synergy 516, Goblin 700, Trex 600E Trex 500 Pro, Trex 250 Pro, Raptor 50, MD 500E with Trex 500 guts, Beam E4.

Offline Chris McClard

  • Newbie
  • *
  • Posts: 27
Re: Bell Crank Assembly
« Reply #5 on: January 10, 2013, 08:23:00 PM »
Okay I completely took apart the bell crank assembly. I found two 15mm shims one between the frame bearing and the outside elevator bell crank and the other was between the outside bell crank and the bell rank. I didn't see anything in the manuel about shims or the kit coming with shims, should this not be there?
Logged
Chris McClard
Fly It Like You Hate It!!!
Synergy N9, Synergy N5c, Synergy 516, Goblin 700, Trex 600E Trex 500 Pro, Trex 250 Pro, Raptor 50, MD 500E with Trex 500 guts, Beam E4.

Offline RichL

  • Synergy Veteran
  • *
  • Posts: 802
Re: Bell Crank Assembly
« Reply #6 on: January 10, 2013, 10:00:38 PM »
Previous post from Matt.  Hopes this helps.



The shims should never go anywhere but on the outside of the ccpm shaft. Placing shims in between bell cranks will cause binding as you are essentially taking up more space on the shaft. The shims should only be used on the outside in order to remove excessive in/out play in the bell crank.

Start with the elevator bell crank side and finish with the opposing side.

The balls in the elevator bell crank can interfere with the frames by a few thousandths of an inch. This was kept the way it is in order to maintain the perfect CCPM geometry for the outside bell cranks. To fit this correctly, simply file or grind off a few thousandths from the threaded portions of the elevator bell crank balls. This should only take a few minutes.


Thanks,

Matt
Logged
Synergy E5: Scorpion HKIII 4025-1100, CC ICE2 120HV, Rail 556/96, V-Bar Silverline

Synergy E7: Quantum 4530-500, CC ICE2 160HV, Rail 716/116, V-Bar Silverline

Offline Chris McClard

  • Newbie
  • *
  • Posts: 27
Re: Bell Crank Assembly
« Reply #7 on: January 10, 2013, 10:17:30 PM »
This helps a bunch. Binding is exactly what caused the bearings to go bad. It makes sence now that this is brought to light. I was already thinking about grinding the ball ends to keep them off the frame. After reinstalling everything works as smooth as butter. Thanks guys for all your help.   
« Last Edit: January 11, 2013, 11:57:28 AM by 3Dflyen »
Logged
Chris McClard
Fly It Like You Hate It!!!
Synergy N9, Synergy N5c, Synergy 516, Goblin 700, Trex 600E Trex 500 Pro, Trex 250 Pro, Raptor 50, MD 500E with Trex 500 guts, Beam E4.

Offline RichL

  • Synergy Veteran
  • *
  • Posts: 802
Re: Bell Crank Assembly
« Reply #8 on: January 11, 2013, 06:55:59 PM »
No problem, happy we could assist.


Rich
Logged
Synergy E5: Scorpion HKIII 4025-1100, CC ICE2 120HV, Rail 556/96, V-Bar Silverline

Synergy E7: Quantum 4530-500, CC ICE2 160HV, Rail 716/116, V-Bar Silverline

Offline Kevin Feil

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2100
Re: Bell Crank Assembly
« Reply #9 on: January 11, 2013, 09:22:55 PM »
This is one of those Tribal knowledge things when it comes to building the N5/N5c kit for the first time. It's gets guy more times than not. lol  I remember the first Synergy N5 I ever built I found out the hard way myself.. Also pay close attention in the build tips and tricks about the shoulder bearings that go into the frames and how to secure them.. this is another Gotcha, also belt tightness (Soon to be a non issue with the release of the TT) also the tail output shaft phasing. Study these well, and you will never fly another Brand 600 class heli again  ;). The N5c is without a doubt the best 600 class nitro on the Market!!! have fun

Kevin
Logged
Team Synergy
Team Futaba
Team Scorpion
Team Morgan Fuels

flyalan

  • Guest
Bell Crank Assembly
« Reply #10 on: January 11, 2013, 09:36:33 PM »
Quote from: Kevin Feil on January 11, 2013, 09:22:55 PM
..... The N5c is without a doubt the best 600 class nitro on the Market!!! have fun

Kevin

What Kevin said!  I smile every time I fly mine :-)

Cheers

Alan

Alan Butler
Team Synergy
Logged

Offline Chris McClard

  • Newbie
  • *
  • Posts: 27
Re: Bell Crank Assembly
« Reply #11 on: January 11, 2013, 09:59:02 PM »
It's killing me to fly it, but want everything perfect before I do. The whole FBL is got me scared chitless, because I've never set one up or even mounted one. So don't know a whole lot about em. Like if I can run a 2s lipo strate into it without a reg. Or what sensor do you run for the Gov.
Logged
Chris McClard
Fly It Like You Hate It!!!
Synergy N9, Synergy N5c, Synergy 516, Goblin 700, Trex 600E Trex 500 Pro, Trex 250 Pro, Raptor 50, MD 500E with Trex 500 guts, Beam E4.

Offline Kevin Feil

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2100
Re: Bell Crank Assembly
« Reply #12 on: January 11, 2013, 10:08:11 PM »
Personally,

 get the CGY750 with the new Firmware! the Governor is the best, and now with the new Software version it is Back on top of the Podium! I am running it on my latest N5c build...(yet to be Maiden-ed But I run it on my other Birds. You think your smiling now? Just wait till you pull on the sticks with that set-up ;)

BR,

Kevin
Logged
Team Synergy
Team Futaba
Team Scorpion
Team Morgan Fuels

flyalan

  • Guest
Bell Crank Assembly
« Reply #13 on: January 11, 2013, 10:16:53 PM »
Mine originally flew with a Helicommand and an external GOV. Went back to the CGY750 and with the new firmware it's awesome!
Just put a CGY750 in a MiniTitan. Flew that combo today and again the CGY750 rocks.

Cheers
Alan
Logged

Offline Chris McClard

  • Newbie
  • *
  • Posts: 27
Re: Bell Crank Assembly
« Reply #14 on: January 11, 2013, 11:59:49 PM »
Thought you had to use Futaba radio only with those? I'm JR plus I've already got a new full size blue Vbar 5.2pro.
Logged
Chris McClard
Fly It Like You Hate It!!!
Synergy N9, Synergy N5c, Synergy 516, Goblin 700, Trex 600E Trex 500 Pro, Trex 250 Pro, Raptor 50, MD 500E with Trex 500 guts, Beam E4.
Pages: [1] 2
« previous next »