November 24, 2024, 03:54:47 AM
« previous next »
Pages: [1] 2

Author Topic: Another 1st time nitro build  (Read 6184 times)

Offline bmclaurin

  • Member
  • **
  • Posts: 89
Another 1st time nitro build
« on: February 14, 2013, 05:15:11 PM »
Been flying electrics for a couple years now, and I currently own an E5 and E7. Decided to take the plunge into nitro with an N5c. Can someone give me some feedback on my planned setup?

N5c
O.S. 55HZ-R DRS
O.S. PowerBoost II
Futaba BLS 156HV cyclic
Futaba BLS 256HV rudder
Futaba S9650 throttle
vBar Full Silverline
Rail 606 mains
Rail 96 tail
Pulse 3600mAH 7.4v RX-Ultra
Gryphon Extreme-Heli GVR-7020B w/ slide switch
Futaba R6202SBW rx
Switch-Glo Pro remote
Spektrum RevLimit rpm sensor
KDE backplate sensor bracket
O.S. bubbleless clunk
FBL rotors titanium turnbuckles

EDIT:  If it matters, I use a Futaba 8FG Super TX.
« Last Edit: February 14, 2013, 05:23:28 PM by bmclaurin »
Logged
Electric: Synergy E7SE, Synergy E5, Logo 600SX, Henseleit TDR
Nitro: Synergy N5c, Synergy N7

Offline Flat Eric

  • Newbie
  • *
  • Posts: 46
  • Wants to be in Team Synergy :)
Re: Another 1st time nitro build
« Reply #1 on: February 14, 2013, 05:25:32 PM »
Very nice setup  :)  but why have a regulator and HV servos?
Logged

Offline bmclaurin

  • Member
  • **
  • Posts: 89
Re: Another 1st time nitro build
« Reply #2 on: February 14, 2013, 05:29:32 PM »
My throttle servo is not HV, so I thought the regulator was necessary.
Logged
Electric: Synergy E7SE, Synergy E5, Logo 600SX, Henseleit TDR
Nitro: Synergy N5c, Synergy N7

Offline Yanick Larouche

  • Field Representative
  • Sr. Member
  • ****
  • Posts: 434
Another 1st time nitro build
« Reply #3 on: February 14, 2013, 06:02:32 PM »
Yes. I use spektrum regulator!

http://www.spektrumrc.com/Products/Default.aspx?ProdID=SPMVR5203

This regulator work well!

Yan
Logged
Team Synergy

Offline Chris Sexton

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2729
  • Admiral, There be whales here!
Another 1st time nitro build
« Reply #4 on: February 14, 2013, 06:12:52 PM »
I run that same motor and gyro setup on  mine and love it!


Sent from my iPhone using Tapatalk
Logged
Chris Sexton
Synergy Factory Specialist / Rail Blades / Team Scorpion

Offline Kevin Feil

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2100
Re: Another 1st time nitro build
« Reply #5 on: February 14, 2013, 10:58:13 PM »
I ran a similar set up, insted of 96mm tails I ran 106 rail tail. Otherwise she is going to be a Beast!

congrats on the Build!

Best,

Kevin
« Last Edit: February 15, 2013, 08:00:47 AM by Kevin Feil »
Logged
Team Synergy
Team Futaba
Team Scorpion
Team Morgan Fuels

Offline Ross Lawton

  • Factory Specialist
  • Synergy Veteran
  • *****
  • Posts: 793
Re: Another 1st time nitro build
« Reply #6 on: February 15, 2013, 02:51:31 AM »
Very nice setup you have got there! 8)

The engine and pipe combo should be an absolute powerhouse!!

Congrat's on the new build, enjoy it! and if you have any questions just give us a shout.  :)

Cheers,
Ross
Logged
Team Synergy - UK

Offline Flat Eric

  • Newbie
  • *
  • Posts: 46
  • Wants to be in Team Synergy :)
Re: Another 1st time nitro build
« Reply #7 on: February 15, 2013, 05:36:31 PM »
Quote from: bmclaurin on February 14, 2013, 05:29:32 PM
My throttle servo is not HV, so I thought the regulator was necessary.

You could buy a voltage stepdown, that plugs in to the servo plug which would take it down to 5v
I think that on the vbar the throttle servo port is not the full voltage, so you wouldn't need a hv servo, don't quote me on this, you would need to check, I have hv throttle servos on all my vbar Helis.
Logged

Offline bmclaurin

  • Member
  • **
  • Posts: 89
Re: Another 1st time nitro build
« Reply #8 on: February 16, 2013, 04:36:15 PM »
Thanks, guys. Picked up my kit last night, but the engine and electronics won't arrive for a few more days. Starting the airframe assembly this weekend. I'll post a few pics along the way. Just barely getting started at the moment.


[attachment deleted by admin]
« Last Edit: February 16, 2013, 04:42:42 PM by bmclaurin »
Logged
Electric: Synergy E7SE, Synergy E5, Logo 600SX, Henseleit TDR
Nitro: Synergy N5c, Synergy N7

Offline Kevin Feil

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2100
Re: Another 1st time nitro build
« Reply #9 on: February 16, 2013, 08:10:06 PM »
Lookin Good Brother, Lookin good! congrats on the build.

Kevin
Logged
Team Synergy
Team Futaba
Team Scorpion
Team Morgan Fuels

Offline bmclaurin

  • Member
  • **
  • Posts: 89
Re: Another 1st time nitro build
« Reply #10 on: February 17, 2013, 04:27:04 PM »
Well, finished up the airframe this afternoon. Now I'm just waiting for my engine and electronics, which should be here in a few days. Looking forward to maidening her hopefully next weekend.

Barry
Logged
Electric: Synergy E7SE, Synergy E5, Logo 600SX, Henseleit TDR
Nitro: Synergy N5c, Synergy N7

Offline Chris Sexton

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2729
  • Admiral, There be whales here!
Another 1st time nitro build
« Reply #11 on: February 17, 2013, 04:40:08 PM »
Looks great!
Logged
Chris Sexton
Synergy Factory Specialist / Rail Blades / Team Scorpion

Offline bmclaurin

  • Member
  • **
  • Posts: 89
Another 1st time nitro build
« Reply #12 on: February 23, 2013, 01:13:01 PM »
Starting to come together now. Just need to run my fuel lines, install the Switch Glo Pro and RPM sensor, and secure my antenna wires. I really like the Gryphon remote LED switch.
« Last Edit: February 23, 2013, 01:15:34 PM by bmclaurin »
Logged
Electric: Synergy E7SE, Synergy E5, Logo 600SX, Henseleit TDR
Nitro: Synergy N5c, Synergy N7

Offline Darren Lee

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 620
Re: Another 1st time nitro build
« Reply #13 on: February 23, 2013, 01:46:50 PM »
Looks great!  Where is the Vbar sensor?
Logged
Team Synergy / Rail Blades / Morgan Fuel

Offline bmclaurin

  • Member
  • **
  • Posts: 89
Re: Another 1st time nitro build
« Reply #14 on: February 23, 2013, 02:03:11 PM »
On the underside of the servo tray.
Logged
Electric: Synergy E7SE, Synergy E5, Logo 600SX, Henseleit TDR
Nitro: Synergy N5c, Synergy N7
Pages: [1] 2
« previous next »