November 23, 2024, 04:05:42 PM
« previous next »
Pages: [1]

Author Topic: Tail in the grass?  (Read 2972 times)

Offline Barry Tilson

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 617
  • Perspective Visuals
Tail in the grass?
« on: July 27, 2013, 10:28:05 AM »
So I'm used to take off and landings on payment or nice take off spot. What does everyone do with deeper grass where the tail blades are an inch or two in?
No big deal just let it weed-wack?
Some sort of landing board?
I have I've seen sliding autos and everything in-between for landings.
Seems to put a load in the tail section.
Thoughts?
Logged
Perspective Visuals

flyalan

  • Guest
Tail in the grass?
« Reply #1 on: July 27, 2013, 10:34:07 AM »
Lawnmower ? :-)

Our field is grass and the person that does the mowing keeps the runway pretty short but in the morning hours the sun can be a challenge. We fly off to the right behind the runway but the grass is longer. Most if my landings are done there. Yes I do make divots but unless its a really botched landing no harm is done other than grass stains on the tail blades.

Cheers
Alan
Logged

Offline Barry Tilson

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 617
  • Perspective Visuals
Tail in the grass?
« Reply #2 on: July 27, 2013, 03:18:51 PM »
Just flip it inverted and cut the grass! LOL. I can see me out at the local soccer field mowing a landing pad.
Logged
Perspective Visuals

flyalan

  • Guest
Tail in the grass?
« Reply #3 on: July 27, 2013, 06:36:55 PM »

Quote from: PerspectiveVisuals on July 27, 2013, 03:18:51 PM
Just flip it inverted and cut the grass! LOL. I can see me out at the local soccer field mowing a landing pad.

Lol.....
Logged

Offline Kevin Feil

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2100
Re: Tail in the grass?
« Reply #4 on: July 27, 2013, 07:17:03 PM »
+1 just flip that biatch and cut dat chit,,



K
Logged
Team Synergy
Team Futaba
Team Scorpion
Team Morgan Fuels

Offline Barry Tilson

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 617
  • Perspective Visuals
Tail in the grass?
« Reply #5 on: July 27, 2013, 09:23:53 PM »
Can't wait to hang with this group!! LOL
Logged
Perspective Visuals

Offline Kevin Feil

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2100
Re: Tail in the grass?
« Reply #6 on: July 27, 2013, 09:54:33 PM »
We have fun! ;D

K
Logged
Team Synergy
Team Futaba
Team Scorpion
Team Morgan Fuels

Offline RichH

  • Newbie
  • *
  • Posts: 45
Tail in the grass?
« Reply #7 on: July 28, 2013, 01:31:18 PM »
In tallish grass I notice wear on the tips of the tail blades. I rebuild the tips with thick super glue or JB weld and keep on flying.


Rich
Logged

flyalan

  • Guest
Re: Tail in the grass?
« Reply #8 on: July 28, 2013, 04:16:54 PM »
Quote from: RichH on July 28, 2013, 01:31:18 PM
In tallish grass I notice wear on the tips of the tail blades. I rebuild the tips with thick super glue or JB weld and keep on flying.


Rich


Not sure if I would recommend using KB weld on blades.  CA maybe.  Are you balancing the blades afterwards?


Cheers
Alan
Logged

Offline Barry Tilson

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 617
  • Perspective Visuals
Tail in the grass?
« Reply #9 on: July 28, 2013, 09:39:14 PM »
My tail drive train sounds louder than it did on spool down. Kind of gear train noise don't remember it making that noise before.
Logged
Perspective Visuals

Offline Kevin Feil

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2100
Re: Tail in the grass?
« Reply #10 on: July 30, 2013, 05:10:48 PM »
Time for an "Annual. Inspection ".


Kevin
Logged
Team Synergy
Team Futaba
Team Scorpion
Team Morgan Fuels

Offline RichH

  • Newbie
  • *
  • Posts: 45
Tail in the grass?
« Reply #11 on: July 31, 2013, 10:32:00 PM »
Quote from: flyalan on July 28, 2013, 04:16:54 PM
Quote from: RichH on July 28, 2013, 01:31:18 PM
In tallish grass I notice wear on the tips of the tail blades. I rebuild the tips with thick super glue or JB weld and keep on flying.


Rich


Not sure if I would recommend using KB weld on blades.  CA maybe.  Are you balancing the blades afterwards?


Cheers
Alan

I sand it back to the original shape. The tips seem tougher as a result.


Rich
Logged

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Re: Tail in the grass?
« Reply #12 on: August 03, 2013, 12:05:40 PM »
Quote from: Kevin Feil on July 27, 2013, 07:17:03 PM
+1 just flip that biatch and cut dat chit,,



K

Hahaha!
Logged
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com
Pages: [1]
« previous next »