November 21, 2024, 10:56:00 AM
« previous next »
Pages: [1]

Author Topic: Ikon Help  (Read 3470 times)

Offline birddawgg

  • Member
  • **
  • Posts: 51
Ikon Help
« on: January 20, 2014, 07:41:58 PM »
Hey ya'll, I normally fly with the CGY 750 but a friend talked me into trying one. However after the complete set up. When I perform the test at the end the swash corrects the wrong way. It moves with the tilt not against it.


I use a Futaba 8FG with an SBus receiver on an E5s.
Logged
Synergy, Futaba, Cool Power, YS,OS

Offline Chris Sexton

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2729
  • Admiral, There be whales here!
Re: Ikon Help
« Reply #1 on: January 20, 2014, 07:46:18 PM »
Hello!

I have a couple of questions.

1. Does the swash respond to input correctly?
 IE Left aileron tilt left, forward elevator tilt forward?
2. Does pitch travel correctly?

If all of these are true, then go back into the setup and on the 9th tab of the basic setup wizard, double check that your ikon is oriented the way you choose.  This orientation combined with assuming you have correct travels is how the ikon knows which way to compensate for.
Logged
Chris Sexton
Synergy Factory Specialist / Rail Blades / Team Scorpion

Offline birddawgg

  • Member
  • **
  • Posts: 51
Re: Ikon Help
« Reply #2 on: January 20, 2014, 07:59:57 PM »
Yes Chris all is correct elevator, aileron and pitch. I have the unit mounted top up, wires back and that orientation selected in the set up.
Logged
Synergy, Futaba, Cool Power, YS,OS

Offline birddawgg

  • Member
  • **
  • Posts: 51
Re: Ikon Help
« Reply #3 on: January 20, 2014, 08:39:42 PM »
Okay so, I have mounted the box top up and wires back. I changed the selection to top up wires forward and now the swash corrects as it should. So Ikon built this unit orientated the wrong way?
« Last Edit: January 20, 2014, 09:22:53 PM by birddawgg »
Logged
Synergy, Futaba, Cool Power, YS,OS

Offline Chris Sexton

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2729
  • Admiral, There be whales here!
Re: Ikon Help
« Reply #4 on: January 20, 2014, 10:32:36 PM »
Quote from: birddawgg on January 20, 2014, 08:39:42 PM
Okay so, I have mounted the box top up and wires back. I changed the selection to top up wires forward and now the swash corrects as it should. So Ikon built this unit orientated the wrong way?


How about the swash setup page? Do you have the right type of swash, not only 120 but with elevator servo in the back? That makes a difference too.
Logged
Chris Sexton
Synergy Factory Specialist / Rail Blades / Team Scorpion

Offline birddawgg

  • Member
  • **
  • Posts: 51
Re: Ikon Help
« Reply #5 on: January 21, 2014, 12:13:32 PM »
Yes I have the swash set to HR-3 120 the elevator or number servo is to the rear.
Logged
Synergy, Futaba, Cool Power, YS,OS

Offline Chris Sexton

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2729
  • Admiral, There be whales here!
Re: Ikon Help
« Reply #6 on: January 21, 2014, 01:46:36 PM »
Does the elevator comp correctly?  Before you swapped the orientation that is.

If it were me, I wouldn't like running with orientation set wrong.  It would bug me.  I would factory reset the ikon, double check that the servos are in the right place. ON the iKON with the elevator servo in the rear, Right side aileron is servo 1, elevator is 2, and left side aileron is servo 3.  I have seen comps be wrong when 1 and 3 are mistakenly reversed. But this will also throw off your servo travel directions.
Logged
Chris Sexton
Synergy Factory Specialist / Rail Blades / Team Scorpion

Offline birddawgg

  • Member
  • **
  • Posts: 51
Re: Ikon Help
« Reply #7 on: January 21, 2014, 02:02:56 PM »
Yes the swash moves correctly in every direction in either orientation. Just the swash corrects wrong when the unit is set to top up, wires back as mounted. If I set it to top up wires forward (not mounted that way) everything still moves correctly and the swash corrects the right way. I will do a reset again and start from scratch one more time. I have contacted Ikon and they believe that I need to do a reset as well. So we will see.
Logged
Synergy, Futaba, Cool Power, YS,OS

Offline byHISgrace

  • Newbie
  • *
  • Posts: 1
Re: Ikon Help
« Reply #8 on: February 04, 2014, 10:40:21 PM »
Make sure that the travels move in the correct direction in the TX page of the basic wizard. Matt
Logged
Pages: [1]
« previous next »