November 23, 2024, 04:41:03 PM

Author Topic: Popped a main grip link in flight - E7  (Read 1537 times)

Offline Aterren

  • Newbie
  • *
  • Posts: 31
Popped a main grip link in flight - E7
« on: September 06, 2014, 09:21:51 PM »
A few weeks ago I had the swash side of the main grip link pop in flight.   Fortunately I kept it out of the 6' tall corn field and only damaged skids the 52T tail drive gear.
I would say my good luck continues.

Now for a question: why?   I did a thorough pre flight including giving the head / links a good tug.   The links were new maybe 100 flights ago.   I was running ~2050 RPM and the link popped as I rolled aggressively on the down line of a big cuban eight.  It was an agressive roll using full stick travel (vbar, 8 degrees, 100 pct agility, 30 pct paddle sim).   

What are your thoughts / experiences / recommendations?  Should i be replacing my links more often?  Did I get too agressive? 

Thanks!
Adrien



Offline curmudgeon

  • Synergy Veteran
  • *
  • Posts: 578
Re: Popped a main grip link in flight - E7
« Reply #1 on: September 06, 2014, 10:55:16 PM »
Sorry about the crash.  It's very unnerving when a crash is due to a mechanical failure.  Is it possible you may have Boto-Sized that particular link a little too loose?

Offline Mike Spano

  • Synergy Hero
  • **
  • Posts: 1038
Re: Popped a main grip link in flight - E7
« Reply #2 on: September 07, 2014, 06:53:28 AM »
Sounds like that may have been what happened. Just one turn too many with the sizer. Glad to hear that you saved it as well as you did though!
Team Synergy
Rail Blades
TRM Power
Team Byron Fuels
MKS Servos

Offline Aterren

  • Newbie
  • *
  • Posts: 31
Re: Popped a main grip link in flight - E7
« Reply #3 on: September 08, 2014, 08:34:26 AM »
Yes, I suppose that is possible.  I have always sized so they just fall under their own weight.  Is that looser than you guys go?


Sent from my iPad using Tapatalk HD

Offline curmudgeon

  • Synergy Veteran
  • *
  • Posts: 578
Re: Popped a main grip link in flight - E7
« Reply #4 on: September 08, 2014, 08:55:19 AM »
I size the tail links loose, but not to the point they fall on their weight.  I size the head links a little tighter, and let them loosen up after a few flights. 

Offline Aterren

  • Newbie
  • *
  • Posts: 31
Re: Popped a main grip link in flight - E7
« Reply #5 on: September 09, 2014, 09:12:04 AM »
I will replace them all before flying again.  Thanks

Offline Rodney Kirstine

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 2112
Re: Popped a main grip link in flight - E7
« Reply #6 on: September 09, 2014, 10:33:11 AM »
Yes, I suppose that is possible.  I have always sized so they just fall under their own weight.  Is that looser than you guys go?
That is looser than I shoot for on mine. 
Rodney

Team Synergy

Offline Cliff Chmiel

  • Synergy Veteran
  • *
  • Posts: 588
  • Cliff
Re: Popped a main grip link in flight - E7
« Reply #7 on: September 09, 2014, 04:36:38 PM »
In my old nitro days, if you could pop It off with you fingers it to loose, and with the head speed you run now, I would think you need tighter, back then if you were running 2100 or 2200 it was screaming, had no govs then
Cliff

Offline Aterren

  • Newbie
  • *
  • Posts: 31
Re: Popped a main grip link in flight - E7
« Reply #8 on: September 10, 2014, 05:41:02 PM »
...if you were running 2100 or 2200 it was screaming, had no govs then

I was running around roughly 1950 when it popped.   2200 on a 700 is screaming in my book.