New N7 Owner!

[enz5573]

Hi, just ordered my new N7 kit!! along with rail mains & tail blades!
so cranked up! can't wait..

I am not new to nitro's.. had some Raptor 50's 90's and N9. current heli's, Trex 6oon,700n both FBL.I am an all futaba & YS guy. I am just curious of what some of your setup's are FBL system's,servos,motors,gov,exc.
Thanks

[Mike Spano]

congrats! you will love it! its such a light bird! i was flying mine over the snow this morning (dont get much snow in AL, i am always wanted to fly over the snow, so i finally did it!)

mine is as follows....

696mm mains
106mm tails
O.S. 105 HZR (running 22.5% byrons)
Hatori SB-22FH 105 3D Pipe
Full size silver line VBar
VBar Gov (1650, 1800, and 1950)
Futaba Servos all around
2 cell lipo direct

[enz5573]

Thanks man! that's cool, looking forward to it! I am from N.Y. snow and very cold this year!

[rcnut]

Welcome!

I have one flight on mine, and it is awesome!!! I have a little adjusting to do in the Spartan controller, but that's basically to taste.

Mine has the following;

OS105HZ/R with MP7, HeliX 715, 104 KBDD on the back
Spartan Vortex VX1n
MKS HBL950s on cyclic
Savox 1290 on throttle
MKS HBL980 on tail
2 Spektrum DSMX

[Ross Lawton]

Congratulations and welcome to the Forum and the Synergy family! 

My N7 specification is as follows:

OS 105HZ-R DRS Engine
Hatori SB-22FH 105 3D Pipe
Futaba BLS272SV Servos on Cyclic
Futaba BLS276SV Servo on Rudder
Futaba S3072HV Servo on Throttle
Futaba CGY750 Flybarless Controller
Futaba R7008SB Receiver
Scott Grey Reactor HVX Set to 7.4v
GensAce 2200 3S2P Rx Pack feeding the reactor 11.1v
Rail Blades 696 Flybarless Main Blades
Rail Blades 106 Tail Blades

Hope this helps, if you have any questions during your build just give us a shout and we will be more than happy to help. 

Cheers,
Ross

[Kevin Feil]

Welcome to the Synergy Family.


K

[Richard Rollins]

Welcome,. The n7 is a beast and a blast to fly.

[Greg Jackson]

Welcome to the forum!

[enz5573]

Hi, thank you to all for the warm welcome and sharing your setups! As soon as I start to build I will post some pics, Thanks again!!

[enz5573]

Hi all...got my heli yesterday! I started on my build. So far I am very impressed with the quality.

[Rodney Kirstine]

Sweet!  I flew mine today for the first time in several months and man had I missed it! The N7 is by far my favorite.

[enz5573]

Hi, Have a question Pitch Slider Assembly..The manual says to CA or Epoxy the Tail Slider Lock Ring, Is every one CA or Epoxying the Tail Slider Lock Ring?
Thanks

[rcnut]

I did not do that to mine. I haven't had a problem with them in the past (other helis utilizing this type of lock ring).

[Rodney Kirstine]

I use a bit of CA on mine.

[Mike Spano]

i use thin CA to get under the ring, let that cure, then use med CA to encapsulate the ring and build up a tad on the outside.

on the flip side, i have never had an issue with one that i did not glue either though, but thought i would follow the manual exactly