November 23, 2024, 06:22:19 PM

Author Topic: fusno  (Read 2329 times)

Offline turner2

  • Member
  • **
  • Posts: 84
fusno
« on: January 12, 2017, 04:58:19 PM »
Is there anything that can be done with a fusno canopy other than heat it to keep it off main gear. Mine keeps drawing back into the gear after a while?

Offline Danny Dugger

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 636
Re: fusno
« Reply #1 on: January 12, 2017, 05:57:30 PM »
Keep some paper towels/rags/pieces of foam/cut pieces of pool noodle/etc. between the main gear and canopy at all times while it sits in the hangar. Eventually the canopy will set right, but it takes a long time. If you keep the main gear padded between flights out in the sun over the summer it sets pretty quickly.

Offline cml001

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 684
Re: fusno
« Reply #2 on: January 12, 2017, 08:52:34 PM »
Yep!
Clay
I can fly helicopters... Upside down!

Offline turner2

  • Member
  • **
  • Posts: 84
Re: fusno
« Reply #3 on: January 26, 2017, 04:58:03 PM »
Has anyone ever spaced the rear canopy mounts or slotted the front holes in a fusuno canopy. I put pool noodles in between the gear and canopy it is almost impossible on my 2 helis to get the keychain retainers in. I have 3 and just order 2 more. I know Matt said put something between them and heat the canopy mine just shrinks back in after time. It's really hard not to bubble the paint with a heat gun.

Offline Robert "Full" Montee

  • Full Member
  • ***
  • Posts: 141
    • Facebook
Re: fusno
« Reply #4 on: January 26, 2017, 06:53:50 PM »
When it comes to aftermarket canopies, yes and yes, I have moved the holes and spaced the canopy mounts out.
Robert "Full" Montee
Team Synergy / Team Futaba
https://robertstechlib.blogspot.com

Offline turner2

  • Member
  • **
  • Posts: 84
Re: fusno
« Reply #5 on: January 26, 2017, 08:57:25 PM »
Thanks, Robert that is what I am going to do. I don't think it will affect the air flow that was one thing I was wondering about.

Offline Robert "Full" Montee

  • Full Member
  • ***
  • Posts: 141
    • Facebook
Re: fusno
« Reply #6 on: January 27, 2017, 04:20:28 PM »
I haven't experienced airflow issues.
However one of my canopies was a little thin in the back.
During fast backwards flight I could see the canopy flap a little.
I stiffened mine up with fiberglass but I've seen others use some glue and carbon fiber rod.
Robert "Full" Montee
Team Synergy / Team Futaba
https://robertstechlib.blogspot.com

Offline Gabriel Sandoval

  • Field Representative
  • Sr. Member
  • ****
  • Posts: 322
  • If your not crashin' your not trying hard enough..
    • Midwest Heli Boyz
Re: fusno
« Reply #7 on: January 28, 2017, 12:40:05 PM »
Has anyone ever spaced the rear canopy mounts or slotted the front holes in a fusuno canopy. I put pool noodles in between the gear and canopy it is almost impossible on my 2 helis to get the keychain retainers in. I have 3 and just order 2 more. I know Matt said put something between them and heat the canopy mine just shrinks back in after time. It's really hard not to bubble the paint with a heat gun.

Use a blow-dryer a heat gun puts out way too much heat and will ruin the paint.
Team Synergy
Team Scorpion
Team Dee Force Aviation
Team YS Performance USA
Looking for a fuel Sponsor

Offline Mike Spano

  • Synergy Hero
  • **
  • Posts: 1038
Re: fusno
« Reply #8 on: January 31, 2017, 08:28:19 AM »
heat gun works, you just have to be careful is all. that's all I have ever used.

as far as airflow goes, don't worry about that at all. I never fly with a canopy at all and they fly just fine.
Team Synergy
Rail Blades
TRM Power
Team Byron Fuels
MKS Servos