April 28, 2024, 11:10:09 AM
« previous next »
Pages: 1 [2] 3

Author Topic: Roll Call  (Read 10977 times)

Offline Darren Lee

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 620
Re: Roll Call
« Reply #15 on: September 23, 2011, 06:05:27 PM »
N5c
O.S. 55HZ
Funtech B320
BLS253s on cyclic
9256 on tail
9257 on throttle
AR7100R with Revlimit
BeastX v3
Hyperion 1450mAh 6.6v LiFe
Logged
Team Synergy / Rail Blades / Morgan Fuel

nwmtech

  • Guest
Re: Roll Call
« Reply #16 on: September 27, 2011, 01:11:26 AM »

N5c FBL
BeastX V3
OS55HZ
Funtech B320
AR7100r at 2180rpm
Hyperion 1300mah 2s
BLS 451's
BLS 251
9257 throttle
Rail 606's
Rail 96's


Logged

Offline breezyjr

  • Newbie
  • *
  • Posts: 16
Re: Roll Call
« Reply #17 on: October 06, 2011, 11:07:31 PM »
N5

KDE 60 with matching pipe
Outrage 9188 Cyclics
Outrage 9180 Tail
jr mini HV throttle servo
FBL head
Full sized V-bar blue line with 701 governor sensor
Mavrikk 620 mains
Edge 95
SS screw kit
PushGlo remote glow starter...
TP 2s2p 3800 Rx
Logged
Sylphide 90 with Super Gracy 2 fuse (was Scott Gray's) Vibe 90SG FB & FBL, Vibe 50 FBL, Srimok 90n (x2) & FaiFa (Cyber Head), Synergy N5, E6, TDR, Raptor 90SE, 700E F3C, T600 ESP & T600NSP, T500, T450 Pro FBL, E-Aurora, Logo 600SE & 500SE, Beam E4, Furion 450, T450v2, McpX, What's Next?

Offline Brandon Bartolomucci

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1007
Re: Roll Call
« Reply #18 on: October 07, 2011, 08:27:09 PM »
Good stuff in here all the way around. I finally was able to score a set of the Rail tail blades as Experience RC got some in. Can't wait to try them out.
Logged
Regards,
Brandon Bartolomucci
Team Synergy; Scorpion; & Bavarian Demon

Offline breezyjr

  • Newbie
  • *
  • Posts: 16
Re: Roll Call
« Reply #19 on: October 08, 2011, 07:30:50 AM »
Quote from: Brandon Bartolomucci on October 07, 2011, 08:27:09 PM
Good stuff in here all the way around. I finally was able to score a set of the Rail tail blades as Experience RC got some in. Can't wait to try them out.

Ditto.... mine will be here Monday, I assume.  But, I can't wait to "hear" the difference between my Mavvrikk blades and the Rail...  I actually order two sets, so if I like 'em, I'll put the other set on my T600.

Synergy and Matt Botos ROCK!
Never seen a Marquee function on a forum before... just had to try it....  hehe

Joe_Breezy
« Last Edit: October 08, 2011, 07:32:35 AM by breezyjr »
Logged
Sylphide 90 with Super Gracy 2 fuse (was Scott Gray's) Vibe 90SG FB & FBL, Vibe 50 FBL, Srimok 90n (x2) & FaiFa (Cyber Head), Synergy N5, E6, TDR, Raptor 90SE, 700E F3C, T600 ESP & T600NSP, T500, T450 Pro FBL, E-Aurora, Logo 600SE & 500SE, Beam E4, Furion 450, T450v2, McpX, What's Next?

Offline Ross Lawton

  • Factory Specialist
  • Synergy Veteran
  • *****
  • Posts: 793
Re: Roll Call
« Reply #20 on: October 12, 2011, 06:05:16 AM »
N5 - Flybarred
O.S. 55HZ
Hatori SAB 55 Pipe
BLS 451 Cyclic servos
BLS 251 Tail servo
GY520 Gyro
Spektrum H5000 on throttle
Radix 600SB Main Blades
Radix 92 Tail Blades
Spektrum AR7100R
DX7SE Radio


N5C - Flybarless
O.S. 55HZ-R
Hatori SAB 55 Pipe
BLS 451 Cyclic servos
BLS 251 Tail servo
CGY750 Flybarless System
Spektrum H5000 on throttle
Rail 606 Main Blades
Rail 96 Tail Blades
Futaba 8FG Super Radio
Logged
Team Synergy - UK

Offline flyboynellor

  • Newbie
  • *
  • Posts: 26
Re: Roll Call
« Reply #21 on: November 04, 2011, 12:46:08 PM »
N5C FBL
OS 55HZ
Funtech B320
CGY750
Futaba BLS 252 Cyclic
JR DS8900G Tail
Futaba S9650 Throttle
Futaba R6203SB Receiver
Rail 606 Main Blades
CY 93 Tail
Futaba 12FG Radio
Logged
Synergy N5C
Synergy N9

Offline synergy5

  • Newbie
  • *
  • Posts: 17
Re: Roll Call
« Reply #22 on: November 04, 2011, 07:59:44 PM »
n5 fbl
os 55
outrage 55 pipe
align 610s cyclic
align 650 tail
futaba 9257 throttle
edge mains & tail blades
v-bar-pro-gov
perfect reg


n5c fbl
os 55
funtech b320
bls 452s cyclic
bls 251 tail
9650 throttle
rails all round
v-bar-pro-gov
dualsky reg
Logged
n9 fbl v-bar 5.1 ys91 sb19, edge blades
n5 fbl, v-bar 5.1, os 55,55 pipe, edge blades.
n5c fbl,v-bar 5.1,os 55,55 pipe,railed out.

Offline Tommy Wagner

  • Field Representative
  • Sr. Member
  • ****
  • Posts: 418
Roll Call
« Reply #23 on: November 04, 2011, 10:28:42 PM »
N5c FBL
OS 55HZ-R
Power Boost Pipe
Total G
9257 Throttle
JR 8717
JR 8900G
Rail 606 Main
Rail 96 tail
Gryphon regulator for tail and throttle
Switch glow
Perfect regulator fail safe
Gryphon flag pin switch
Volts 2500 7.4v
« Last Edit: November 04, 2011, 10:31:17 PM by Tommy Wagner »
Logged

Offline Tradhunt

  • Newbie
  • *
  • Posts: 25
  • George
Re: Roll Call
« Reply #24 on: November 05, 2011, 05:53:07 PM »
N5C FBL
YS56SR
Funtech
CGY750(for now I might switch iy over to Vbar)
BLS451's cyclic
8900G tail
Align 520 throttle
Perfect Regulators Safe switch DUO Pro
Outrage 3600
Rail 606 mains
Rail 96 tails
Logged
George

Offline ghostrider414

  • Newbie
  • *
  • Posts: 42
Re: Roll Call
« Reply #25 on: November 29, 2011, 07:46:42 PM »
N5C FBL
YS56SR
Funtech
JR8717 X3 cyclic
JR8900 tail
9650 thorttle
VBAR 5.2 Pro
Voltz lifePo4 2100mah 2S6.6V
Rail 606 mains
Rail 96 tails
« Last Edit: November 29, 2011, 07:52:13 PM by ghostrider414 »
Logged
AMA # 891553
Jerry

Offline Jake

  • Newbie
  • *
  • Posts: 24
Re: Roll Call
« Reply #26 on: December 04, 2011, 05:09:13 PM »
N5C FBL
OS 55HZ-R
Hatori 566
CGY750
Hitec 7965MG's on cyclic
BLS251 on tail
Futaba S9650 throttle
Spektrum 6v regulator
Rail 606 mains
Rail 96 tails
Gryphon on-board glow
Logged

Offline Matt Botos

  • Synergy Hero
  • **
  • Posts: 1573
    • Matt Botos
Re: Roll Call
« Reply #27 on: December 13, 2011, 01:11:34 PM »
UPDATE on my N5c

N5c

O.S. 55HZ-R Limited Edition (Black case / Red Head)
OS55 Power Boost II / Hatori SAB55 (Still undecided)
Futaba 6203 RX
BLS 255 Cyclic servos
BLS 256 Tail servo
CGY750
9650 throttle
Rail 606 main
Rail 96 tail
TP 2S 1800mah RX Pack
Logged

Offline jamesc7701

  • Newbie
  • *
  • Posts: 1
Re: Roll Call
« Reply #28 on: December 13, 2011, 07:59:20 PM »
N5C

YS56sr
outrage hyper pipe
cgy750
edge rotor blades
bls351 cyclic
9256 tail
9650 throttle
push glo
Logged

Offline j bomb

  • Newbie
  • *
  • Posts: 4
Re: Roll Call
« Reply #29 on: December 28, 2011, 08:46:21 AM »
Here's mine:

N5c FBL

engine: KME .60
pipe: KME Powerhouse/Mavrikk .70
FBL: Total G
cyclic servos: Savox 1257TG
throttle servo: Futaba 9650
tail servo: Futaba BLS 251
blades: Rail 606/96
radio: Spektrum DX8
other: Hyperion 2100mAh LiFe battery-unregulated to Total G, Spektrum 5203 regulator for tail servo, PushGlo ignitor

Still on the fence about the KME engine, shows awesome performance at times but runs inconsistently.  I started w/ the KME pipe, but suspected that a baffle might be coming loose so I switched to the Mavrikk.  I didn't really get a chance to thoroughly test the new pipe before the weather got cold. I can't wait until it gets warm again here so I can play with it some more.  If I can't get it to my liking, I may just get a new engine, I hear that YS is working on a 60 of their own....
Logged
John Barta
Pages: 1 [2] 3
« previous next »