November 21, 2024, 10:27:00 PM

Author Topic: Bearings  (Read 4602 times)

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Bearings
« on: December 30, 2012, 11:27:36 AM »
I have Boto Lube coming in probably tomorrow for use as a grease on the thrust bearing race.  But I saw someone mention a while back to grease the radial bearing as well.  The manual says nothing about that but is very specific about other things.  The reason I ask is that it was not recommended to use the same oil/grease for both thrust bearing and radial, but there is a grease port on the main head.  Wouldn't the Boto lube get on the radial bearing then?  Just want confirmation, I should FINALLY get started on those parts today. 

Also, I was in a hurry and forgot to pick up Medium CA yesterday, would Thick Slow Cure be ok?  Just making sure before I use it. 
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com

Offline RyanW

  • Full Member
  • ***
  • Posts: 162
Re: Bearings
« Reply #1 on: December 30, 2012, 11:42:44 AM »
Technically the radial bearings are already greased from the bearing factory. Some people like to regrease them, but usually use something more specific for ball bearings like this- http://www.ronlund.com/rcheli-prod/TOOLLU/GREASE.html

Boto Lube is good for thrust bearings and the port on the blade grips should be positioned to grease the thrust bearing assembly. If it gets in the radial bearing, it won't hurt.

CA- Slow Cure is just going to take longer to cure and should have a stronger bond.
-Ryan

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Re: Bearings
« Reply #2 on: December 30, 2012, 11:49:39 AM »
Thank you soooooo much.  Had those two worries.  I won't get a chance to even do a test flight with this until Thursday judging by the weather and when I get it build. 
It seems there are a lot of Synergy people in the Southeast region so my advice to you all is take advantage of today and tomorrow and fly.  It should be rainy Tuesday and wednesday, maybe Thursday.  I'm probably going to concentrate more on building and sim time. 
Working on the sim while I was gone helped tons.  Usually i spend more time flying (real), less on the sim, but I got to improve my backwards flight skills to the point it is effortless and my inverted forwards/backwards feels effortless.  Then I really worked on hurricanes, but I will say doing hurricanes on a real heli feels easier to me, but it was good to work on it on the sim because it was harder.  And finally can do inverted tail in funnels!  Now I'm getting half piro flips down.  This heli is going to be a beast so I have to make sure I can hang on for the ride you know!  But I will spend an entire month getting used to the heli before trying this stuff out.  That is what the other helicopters are for lol. 
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com

Offline RichL

  • Synergy Veteran
  • *
  • Posts: 802
Re: Bearings
« Reply #3 on: December 30, 2012, 04:00:36 PM »
Technically the radial bearings are already greased from the bearing factory. Some people like to regrease them, but usually use something more specific for ball bearings like this- http://www.ronlund.com/rcheli-prod/TOOLLU/GREASE.html

Boto Lube is good for thrust bearings and the port on the blade grips should be positioned to grease the thrust bearing assembly. If it gets in the radial bearing, it won't hurt.

CA- Slow Cure is just going to take longer to cure and should have a stronger bond.

+1
Synergy E5: Scorpion HKIII 4025-1100, CC ICE2 120HV, Rail 556/96, V-Bar Silverline

Synergy E7: Quantum 4530-500, CC ICE2 160HV, Rail 716/116, V-Bar Silverline

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Re: Bearings
« Reply #4 on: December 30, 2012, 05:07:13 PM »
Sounds good!
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Re: Bearings
« Reply #5 on: December 30, 2012, 05:17:22 PM »
Oh yeah, can you use Boto lube on the one way bearing?
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Re: Bearings
« Reply #6 on: December 30, 2012, 05:18:26 PM »
Did anyone notice if the one way had grease on it already when checking?  I wanted to start on doing loctite on the main gear but will wait until I have my Boto lube tomorrow.
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com

Offline Brandon Bartolomucci

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1007
Bearings
« Reply #7 on: December 30, 2012, 05:29:46 PM »
You do not want to use any grease on the one way bearing. You want to use an oil only. Grease is thick and it can also attract dirt and end up ruining your one way.


Regards,
Brandon Bartolomucci
Sent from my iPhone
Regards,
Brandon Bartolomucci
Team Synergy; Scorpion; & Bavarian Demon

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Re: Bearings
« Reply #8 on: December 30, 2012, 05:33:16 PM »
So just use my triflow oil or scorpion oil on the one way right?  Should have the scorpion oil in tomorrow also.  Watching Chris' video again on the front transmission, did anyone use green loctite on the brass retainers?  I don't have any so that is why I wondered.  Not at that part yet, but if mine will not come out would it be safe to leave it be?  Going to start on the front torque tube box now.
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com

Offline Chris Sexton

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2729
  • Admiral, There be whales here!
Re: Bearings
« Reply #9 on: December 30, 2012, 06:15:49 PM »
So just use my triflow oil or scorpion oil on the one way right?  Should have the scorpion oil in tomorrow also.  Watching Chris' video again on the front transmission, did anyone use green loctite on the brass retainers?  I don't have any so that is why I wondered.  Not at that part yet, but if mine will not come out would it be safe to leave it be?  Going to start on the front torque tube box now.

The brass washer need to be loctited into the one way hub. Matt has said this many times. I use green bearing retainer, its better suited for the job.

Yes, Scorpion motor oil will work on the OWB, I use the TriFlow Oil Pen.
Chris Sexton
Synergy Factory Specialist / Rail Blades / Team Scorpion

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Re: Bearings
« Reply #10 on: December 30, 2012, 07:26:55 PM »
Will I be able to find the green at Home Depot?
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com

Offline Chris Sexton

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2729
  • Admiral, There be whales here!
Bearings
« Reply #11 on: December 30, 2012, 07:43:58 PM »
Probably. Red would work but harder to get off if you need to.


Sent from my iPhone using Tapatalk
Chris Sexton
Synergy Factory Specialist / Rail Blades / Team Scorpion

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Re: Bearings
« Reply #12 on: December 31, 2012, 12:05:07 PM »
Ok great so I can use the red I have.  I went to a few stores today and did not find any of the green we are talking about. The green I saw was even stronger than the red.  So just out the red on the exterior and than should be good?
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com

Offline Chris Sexton

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2729
  • Admiral, There be whales here!
Re: Bearings
« Reply #13 on: December 31, 2012, 12:58:01 PM »
wipe some onto the brass ring and insert into the hub. DON'T USE too much that it drips into the OWB, could be fun :0
Chris Sexton
Synergy Factory Specialist / Rail Blades / Team Scorpion

Offline Greg Jackson

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1493
    • inner3.com
Re: Bearings
« Reply #14 on: December 31, 2012, 06:59:57 PM »
I will just put a whisper of it on. 
Synergy & Rail Field Representative
Team Scorpion||Team BK Servos||Team Pulse|

www.inner3.com