September 28, 2024, 05:24:12 PM
« previous next »
Pages: [1]

Author Topic: New E7 Head Block  (Read 3674 times)

Offline Matt Botos

  • Synergy Hero
  • **
  • Posts: 1573
    • Matt Botos
New E7 Head Block
« on: January 30, 2013, 07:12:40 PM »
Hey guys,

I've been working on a few new products that I think you will enjoy. One of them is a new head block for the guys who enjoy the lowered head look. This head is very similar to the E5 design which incorporates the swash follower arms into the head block and has a head axle pivot insert for better collective response + cyclic control. I hope to have this head block available by the end of February.

Here are some pics....

« Last Edit: January 30, 2013, 07:17:57 PM by Matt Botos »
Logged

flyalan

  • Guest
New E7 Head Block
« Reply #1 on: January 30, 2013, 07:20:29 PM »
Great to hear Matt.
Put me down for two when they are ready.

Alan


Alan Butler
Team Synergy
Logged

Offline stevehof

  • Full Member
  • ***
  • Posts: 145
Re: New E7 Head Block
« Reply #2 on: January 30, 2013, 07:49:43 PM »
Very nice! Looks like it uses the same spindle? What's the overall blade height difference between this setup and the stock head When mounted in the lowest position?
Logged

Offline Jean-Luc Bolduc

  • Field Representative
  • Synergy Veteran
  • ****
  • Posts: 614
Re: New E7 Head Block
« Reply #3 on: January 30, 2013, 07:58:16 PM »
Very, very nice !

Going to update my E7's as soon as available.

Great Job Matt.
Logged
Team Synergy

Offline Matt Botos

  • Synergy Hero
  • **
  • Posts: 1573
    • Matt Botos
Re: New E7 Head Block
« Reply #4 on: January 30, 2013, 08:26:20 PM »
It depends on which hole you were using on the old head. I was using the lowest hole.
From the lowest hole, it will drop the head approximately 25mm or 1in.

Thanks,

Matt
Logged

Offline steffgiguere

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 1373
Re: New E7 Head Block
« Reply #5 on: January 30, 2013, 08:37:13 PM »
Wow, very cool, very nice, just might have to upgrade. Your always thinking Matt, congrats.
Logged
Team Synergy, Canada

Offline Ross Lawton

  • Factory Specialist
  • Synergy Veteran
  • *****
  • Posts: 793
Re: New E7 Head Block
« Reply #6 on: January 31, 2013, 02:52:14 AM »
Awesome stuff, very nice!  8)

Add to cart!!  :)

Cheers,
Ross
Logged
Team Synergy - UK

Offline Rodney Kirstine

  • Field Representative
  • Synergy Hero
  • ****
  • Posts: 2112
Re: New E7 Head Block
« Reply #7 on: January 31, 2013, 09:39:04 AM »
I know you mentioned possible boom strikes if one went too low with the modifications.  I'm guessing, based on your pictures, that the one I did with the original E7 head block should be okay?





Logged
Rodney

Team Synergy

Offline Kevin Feil

  • Factory Specialist
  • Synergy Hero
  • *****
  • Posts: 2100
Re: New E7 Head Block
« Reply #8 on: February 04, 2013, 10:51:04 PM »
Looks good, I'm ready for a couple of those. Nice Job  8)!

Kevin
Logged
Team Synergy
Team Futaba
Team Scorpion
Team Morgan Fuels

Offline Chris "CSpaced" Mulcahy

  • Member
  • **
  • Posts: 55
  • Lower!
    • AMA
Re: New E7 Head Block
« Reply #9 on: February 15, 2013, 10:31:52 PM »
Looks nice, is this something we can use on the N5c as well?
Logged
Chris Mulcahy
Team Futaba, Team Castle Creations, Team KDE Direct
Synergy N5c, Synergy E7SE, Synergy E5S

Offline Gregor

  • Newbie
  • *
  • Posts: 31
Re: New E7 Head Block
« Reply #10 on: March 26, 2013, 11:59:45 PM »
I like the design. Will this lowered head require stiffer dampers, or have minimum headspeed, and maximum pitch requirement to prevent clearance issues?
Logged

Offline 360wings

  • Newbie
  • *
  • Posts: 2
Re: New E7 Head Block
« Reply #11 on: March 30, 2013, 09:16:42 PM »
The original post suggested Feb. as approx. release time.. Its almost April, how far off are we from their release?

Also, will the full E6/E7 kits be released with the newer head block or will it be an upgrade option only?

Logged
Pages: [1]
« previous next »